Nail nicks :(
-
the can opener nick's position is designed for wave really, not surge.
It works fine on wave, but on surge, the nick is blocked by the large bit driver.
-
I had to remove the bit driver but even then that can opener was stuck :( If I had shorter nails I don't think I would have been able to take it out at all :(
-
The Wave/Surge can opener has a side mounted nail nick rather than the top mounted nail studs found on most leatherman secondaries. I often have to pry it out with another tool. Fortunately I don't use the Wave can opener very often.
I have to agree 100% on the through-holes on the Wingman/Sidekick. That simple innovation really makes that tool. I wish they would incorporate something like that in the Wave where pushing the lock buttons pushes up the secondaries so you can more easily get to them.
-
I'm thinking like what if I got some fishing line or metal wire and tied it around the inside handle tools and let it poke out a bit. Then it could be sort of like a pull tab.
-
Pull out the large bit drvier (shall be easier to do), can opener will come out with it.
Or do what he said.
that's us mobile
If you read my earlier post I said that I did do that, however even then it was still difficult.
-
No, some how I missed yours.
Might might have to adjust the tension or or it still needs broke in. All of my LM where a little tight at first. After a few days they loosened up and become very smooth. Next time you watch a moive or a show, just open and close the tools. You will find that they will smooth out a bunch at the end of the show.that's us mobile
-
Send it in to Leatherman for adjustment...
-
My surge was the same way. Tight can opener/wire stripper. It loosens up soon enough.
-
The can opener is usually harder to get out than the other tools. :-\
-
It happened to me also with Wenger 557; the philips screwdriver and the wrench didn't want to come out. I brake also my nail but after some time the tools became more fluid
-
On my Surge the nail nick on the can opener is superfluous. Just press the tip of my index finger into the channel with the pad of my fingertip pressed against the opener and "roll" towards my nail, the opener just flips up and my thumb and index finger just pinch and pull it open fully. The weight of the tool pulls and locks it open.
-
@Yalius said:
On my Surge the nail nick on the can opener is superfluous. Just press the tip of my index finger into the channel with the pad of my fingertip pressed against the opener and "roll" towards my nail, the opener just flips up and my thumb and index finger just pinch and pull it open fully. The weight of the tool pulls and locks it open.I'm going to try that, it sounds good :) Doesn't the replaceable bit driver get in the way though?
-
I tried it and it doesn't work for me, my fingers are too big to fit inside the handle :(
-
Look at the side of the opener that rests against the handle. Are there any rub marks?
If it is hard to tell, try using a felt pen, open and close a couple times and then check.
On my BO version it was easy to see that the pointy bit was sticking or making contact.
I gave it a small tap with a hammer and now it works sweet.
Otherwise you could try loosening the tension a little. -
@Cogito said:
I tried it and it doesn't work for me, my fingers are too big to fit inside the handle :(I did just check mine, it's loosened up enough so that I can just rap the handle against my hand and the opener comes out enough to pinch it out. It's probably not technique so much as a low-retention pivot.
-
I hate nail nicks too. I saw a little tool on AG Russell's site once like a little butter knife for nail nicks. Think I might get one.
-
They don't have them now. Called a knife pick. I see others may have them.
-
I saw that in another thread. I need to find a link.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
