Show off your Sak mod's!
-
lightning strike carbon fiber.
I've been wanting to do carbon fiber scales on my Swiss Champ for a while now. A thing of beauty there

It was far easier to work than I thought. I will be ordering some thinner carbon fiber for 91mm mods next.
-
@hiraethus said:
Slow, slow progress but the scales are finally sanded and polished and ready to send to the anodizer (who will slip them into the next run of black for a very reasonable sum):

Nice.
You'll still need to use liner though so the T&T don't fall out. I'd try to make the T&T grooves ride on the same scale, like on the Plus scales, just not pen and tooothpick but toothpick and tweezers. That way you'd only need the liner on one side. -
@enki_ck said:
Nice.
You'll still need to use liner though so the T&T don't fall out. I'd try to make the T&T grooves ride on the same scale, like on the Plus scales, just not pen and tooothpick but toothpick and tweezers. That way you'd only need the liner on one side.Yep. I milled down the scales to make them thinner, planning to use them without liners, then didn't like the way the corkscrew extended a long way past the scale. So I put the liners back in and decided to cut the grooves for T+T. What I should have done is make the shield side scale thin (2mm or so) and used no liner and then tried to get the T+T into the corkscrew side, with a liner. Every day is a school day. :D
-
Nice.
You'll still need to use liner though so the T&T don't fall out. I'd try to make the T&T grooves ride on the same scale, like on the Plus scales, just not pen and tooothpick but toothpick and tweezers. That way you'd only need the liner on one side.Yep. I milled down the scales to make them thinner, planning to use them without liners, then didn't like the way the corkscrew extended a long way past the scale. So I put the liners back in and decided to cut the grooves for T+T. What I should have done is make the shield side scale thin (2mm or so) and used no liner and then tried to get the T+T into the corkscrew side, with a liner. Every day is a school day. :D
You could even mill 3 slots in one scale to accept Toothpick, pen and (shorter) tweezers like on the Vics with electronic scales.
The pattern is there on most newer scales, only theopening for the 3rd slot is left blank.
I do have some short tweezers I don´t need myself that I´d sponsor. -
4 slots, you forgot the pin. ;-)
-
Ha, do you guys have any idea just how long it took me to make those scales? I've probably put 6 or 7 hours work into them. There's no way I'm modifying them now.
-
Many here already made own scales. Personally I spent hours and hours in creating individual scales by hand. Even now, after some practise, I estimate about 4 hours per wood/horn scale (for each side!!) with tools inside. So expect no mercy and add those slots!!! >:D >:D
:D -
@HankSolon said:
4 slots, you forgot the pin. ;-)
Right you are.
would make a nice Alox Plus, don´t you think Hiraethus?
-
Gits.
;) -
Just finished this mod. My Deluxe Flyer Pro. No sharps, just scissors which should be airline friendly.

There is always a way, hack on!
-
-
Black and Silver(aluminum) go well together. Nice job :)
-
Alox with back tools = 8)
-
Very rare to see alox scale with back tools, toothpick and tweezer.
Sent from my HTC One X using Tapatalk
-
Beautiful Work, Well Done

-
Really nice job, especially keeping the toothpick and tweezers! JR
-
Very nice!
that's us mobile
-
Awesome job on the Alox Yeoman hiraethus

-
That is lush! nice job

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




