Cybertool Disappointment :(
-
@kkokkolis said:
SAKs and Multitools are emergency tools. Of course we geeks, a minority of people, like to try them on everything since we have them, just for fun or for the experience of it. I'm not a IT pro but I bought a PC kit once and it is big enough to leave it home. But the SAK is EDCed so that's what I have and that's what I use. You professionals would have the CT as a backup I guess.I most respectfully disagree!
Okay... I'm only a semi-pro really when it comes to big hardware work. I do it semi-regularly, but it's not my primary job. However, when I do do it, my Cybertool is the primary weapon of choice. It's only after the CT can't do a job that I'll (begrudgingly) get a more specialize tool.Just the other week I had to replace a board in a large format printer. Cybertool all the way! Took out a laser and a sensor with the in-line phillips, used the scissor to cut the zip ties to take out the old wiring. Use the flat blade bit to help loosen wire harnesses from the old board. Use the large Phillips bit to unscrew the board. Used the jewelers screwdriver to pry up a ribbon cable harness. Then put it all back together and used the pliers to get at wires in tight areas to pull them through.

Cybertool all the way!! :)
-
I'm glad you disagree cause I adore the CTs.
-
@RimfireNZ said:
Well I've had the chance to use my Cybertool a couple of times working on a few computers and within the context of a computer techs tool I have to say I'm a little disappointed.It's an awesome SAK… it's just not an awesome computer tech tool. I was sort of hoping for it to be awesome and all I'd need considering it's supposed to be built for guys in my industry. I don't have that much to whinge about but:
[li**]The bits it comes with are very limited and are not the most common sizes used on a number of the rigs I work on (I know, easily fixed right?).**[/li]
- It's actually very awkward to use as a screwdriver (it really blows for this when dealing with dozens of small screws).
As a result it almost always end up getting my proper computer toolkit out.
However I took a few action shots for you guys since my three and a half year old MacBook Pro is having issues and I had to rip out my hard drives and replace it with another to see if it was the issue (it wasn't… so I have to buy a new computer… and this last one cost me about $3,300USD by the time I was finished tinkering with it).
That isn't the case, fixing the lack of bits for the CT that fit! I haven't found any that fit.
-
The CT has the essentials... Philips and slotted bits. I don't see what all the negative fuss is about. The CT is an incredible tool and if its bits won't cut it, use a dedicated kit. I bought 2 special hollow handled Craftsman screwdrivers from Sears that have just about every bit and size you could ever want. The cost: about $22 a piece. A steal if you ask me. Hell, it even included T-x security bits!
-
I don't do much hardware fiddling anymore, but Macs... Those machines are built by a tool company wanting to create a market. The number of different and unusual screws to do just basic maintenance on those boxes... shudder (Disclaimer: Several years since last time I dismantled one of them, perhaps they've become better, but it's not like that's the industry trend...)
That said, last time I tried solving a problem with my CT34 it didn't have the correct bit, but that was tightening the pivot on a folding knife. :)
-
Well I've had the chance to use my Cybertool a couple of times working on a few computers and within the context of a computer techs tool I have to say I'm a little disappointed.
It's an awesome SAK… it's just not an awesome computer tech tool. I was sort of hoping for it to be awesome and all I'd need considering it's supposed to be built for guys in my industry. I don't have that much to whinge about but:
[li**]The bits it comes with are very limited and are not the most common sizes used on a number of the rigs I work on (I know, easily fixed right?).**[/li]
- It's actually very awkward to use as a screwdriver (it really blows for this when dealing with dozens of small screws).
As a result it almost always end up getting my proper computer toolkit out.
However I took a few action shots for you guys since my three and a half year old MacBook Pro is having issues and I had to rip out my hard drives and replace it with another to see if it was the issue (it wasn't… so I have to buy a new computer… and this last one cost me about $3,300USD by the time I was finished tinkering with it).
That isn't the case, fixing the lack of bits for the CT that fit! I haven't found any that fit.
I wish Vic did offfer more bits for the Cybertool like LM does.
that's us mobile
-
Well I've had the chance to use my Cybertool a couple of times working on a few computers and within the context of a computer techs tool I have to say I'm a little disappointed.
It's an awesome SAK… it's just not an awesome computer tech tool. I was sort of hoping for it to be awesome and all I'd need considering it's supposed to be built for guys in my industry. I don't have that much to whinge about but:
[li**]The bits it comes with are very limited and are not the most common sizes used on a number of the rigs I work on (I know, easily fixed right?).**[/li]
- It's actually very awkward to use as a screwdriver (it really blows for this when dealing with dozens of small screws).
As a result it almost always end up getting my proper computer toolkit out.
However I took a few action shots for you guys since my three and a half year old MacBook Pro is having issues and I had to rip out my hard drives and replace it with another to see if it was the issue (it wasn't… so I have to buy a new computer… and this last one cost me about $3,300USD by the time I was finished tinkering with it).
That isn't the case, fixing the lack of bits for the CT that fit! I haven't found any that fit.
I wish Vic did offfer more bits for the Cybertool like LM does.
that's us mobile
That just proves LM is a better company! 8)
-
I know it would probably make the layer a bit thicker, but Id still rather it use standard size bits, Id be fine with the tradeoff.
-
Hmmm, wonder if you could mod a LM bit driver to fit a vic?
that's us mobile
-
I know it would probably make the layer a bit thicker, but Id still rather it use standard size bits, Id be fine with the tradeoff.
Agreed, wholeheartedly...
If it could accept 1/4 bits or Victorinox made an adapter then it'd be about perfect.I have seen some precision screwdriver sets on Amazon that include a nut driver, a 1/4" nut driver is sort of a full size bit holder, if it has the ability to hold the bit in question.
here is a picture for example look at the right most black piece in the bits

this kit is only $14, and something like this might be a good starting point to make an adapter
-
@ducttapetech said:
Hmmm, wonder if you could mod a LM bit driver to fit a vic?that's us mobile
That was on one of my start but never get around to finishing projects. I wanted to add the LM bit driver on an alox sak the way the marlin spike is added over a scale cutout. :D
-
I wasn't getting too negative about the tool, it just makes a more awkward screwdriver than I'd hoped for after actually using it a few times. I love the CT as a SAK. I haven't quite worked up to pocket carrying it and leaving my Leatherman behind… but it might happen soon.
And yeah for the tech guys, I do work on a few Macs so I guess I can't complain too much. They're the kind of torx screws… as if that'd stop me opening them up. It's dumb. Easily solved with a few more bits.
I'm a lost cause. I'm actually feeling bad my CT isn't in my EDC bag today :face palm:
-
For me, the Cybertool is one of the best bit drivers in a multitool. Frequently, I will go to the Cybertool first, before getting a dedicated driver. For me, the Cybertool does the job well in over 75% of the cases (maybe much higher). This saves me from going to the workshop for my 4mm microbit driver set.
AND I LOVE the 90 degree position for the torque. :)
-
I made a nice 1/4" adapter for the Philips driver. But in order to add functionality to almost any SAK one should make an adapter for the bottle or can opener. This is difficult since they are wide.
With a magnet the Cybertool holds any 4mm bit. The problem is to find a nice compact holder for those bits. -
When I get my 41 ( any day now ) , I'll prolly put a rare earth magnet in the bit holder . There are quite a few makers of 4mm bits . I don't work on computers . I may make a small pocket bit pouch for additional bits . Personally , I don't need Torox or Posidrive , 0,1,and 2 Phillips , a couple of flats , and a couple of Robertsons will do it for me .
Chris
-

Worked on few machines too, but never ever used kinda specialized tool,
but, of corse, I have Minichamp always at hand

btw, get the real machine for a stack, which runs over time ... :D
not three grand kinda book that even doesn't use the appropriate screws
-
@Caranthanus said:
btw, get the real machine for a stack, which runs over time ... :D
not three grand kinda book that even doesn't use the appropriate screws
Lets not start that convo as no-one ever wins when you talk about religion, politics, or operating system preference :D
-
Sure you do:
Best Religion: Jedi
Best OS: MS-DOS
Best Programming Language: Logo Turtle
Best Multitool: Alox MiniChamp
Best Form of Governement: Monarchy with me as the Monarch
Best SAK: Victorionx CyberToolSee easy, no one is going to disagree or at least not if I ever get to be the Monarch. :P
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
