What did you use your Leatherman for today?
-
Used my Rebar yesterday to remove a 2.5 horsepower pump motor then used the file to remove the bur on some unistrut.
Sent from my SCH-I605 using Tapatalk
-
Getting a digital camera ready for another photo project, the locking tab came off the SD memory card. :ahhh
Took a bit to find the thing, but when trying to put it back (under pressure) shot it off to parts unknown. :ahhh
Grabbed a spare MicroSD Adapter, removed the protection locking tab, and tried unsuccessfully to retro fit it onto the memory card that I needed to be working again. That's when I found a small strip of plastic had come loose, so even if I could had slipped the locking tab back into place it would of fell out anyhow.
Showing a locking tab (top layer removed)

This is how the tab is inserted. Removing, easy. Putting back, best left to thin fingers and younger eyes!


So... dug out the hot melt glue gun. Affixed two layers, and press formed that into place. Once cooled used the Squirt's knife blade to trim the excess, and cut away material in the channel groove. Charge's files were both used. Now the SD card is back and operational.

Think I will be better off if can find a 3rd Hand tool, preferably with a magnifier. A headlamp, as am tired of flashlight-in-mouth technique. And wished there was a Squirt-sized Crunch for times like this - especially at 5AM!
-
I was using my Rebar's screwdriver, but the handles are wobbly. :'(
-
Opened a few boxes of new cigar inventory at the shop today using the Rebar main blade :D
-
@CanadianLMfan said:
I was using my Rebar's screwdriver, but the handles are wobbly. :'(What do you mean when you say the handles are wobbly?
-
@stealth007s said:
Opened a few boxes of new cigar inventory at the shop today using the Rebar main blade :DMmmmm......cigars......
that's us mobile
-

Sorry about the quality of the picture I smashed the rear camera on my iphone so this one was taken with the forward facing camera. But here I am using my Crunch to unbolt a door on a bucket elevator system. The old corroded nuts were no match for the Crunch and a small amount of good old fashioned elbow grease.
Sent from my iPhone using Tapatalk
-
I used the blade on a style cs to finally remove the logos of my bike jacket.
-
@hrvstmn31 said:
I used the blade on a style cs to finally remove the logos of my bike jacket.Very good tool! :D

-
I used the blade on a style cs to finally remove the logos of my bike jacket.
Very good tool! :D

Always in my shirt pocket when I am at work.

-
I used the blade on a style cs to finally remove the logos of my bike jacket.
Very good tool! :D

Always in my shirt pocket when I am at work.

I never leave home without one and I keep one on my desk for easy access.
-
I used my BO Wave to liberate my red and yellow Skeletools from their confining packaging

I feel so much better now! :D. Oh, and the yellow one came with a Leatherman sticker.... bonus!
-
I used the flat driver on my TTi (that I had filed down to an awl of sorts) to dig/chip away at some ice to free a funnel tip outside by a group of buckets. It worked great until I tried to pry the tip out when I thought it was loosened enough. Well it wasn't quite loose enough, and I ended up snapping the whole thing off :o First MT break for me, so the TTi will have to be heading to LM for repair.
-
-
@Monrogue said:
I used the flat driver on my TTi (that I had filed down to an awl of sorts) to dig/chip away at some ice to free a funnel tip outside by a group of buckets. It worked great until I tried to pry the tip out when I thought it was loosened enough. Well it wasn't quite loose enough, and I ended up snapping the whole thing off :o First MT break for me, so the TTi will have to be heading to LM for repair.Breaking a LM is like a right of passage
Good job Kyle!¡! -
GO KYLE
You'll show that funnel tip. -
Its just like driving a car. You dont know your limits unless you have exceded them before. AKA crashing.
Im being dead serious too.
-
Since it broke at the base he"ll only need send in the tool and keep the modified part. I don't feel the mod weakened the driver so he should be good to go.
@Monrogue in the words of DeNiro to Liotta in Goodfellas " Oh, You broke your Cherry"
-
Thanks guys, it was my first MT breakage :D I was definitely prying with it when I shouldn't have been. The pliers finished the job with no trouble, so I got the funnel out of the ice. Now I get to mess with the LM warranty business, but at least they're very good from what I've read here. I just plan on sending the TTi without the broken piece that I modded. I don't think that part is necessary really as the mod should have had no effect on the break considering how I was using it ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

