The Hacked Leatherman Owners Club.
-
Nice job on that Wingman Lowtech
I would love to have my Sidekick-X with Vic scissors.I tried out that mod with an old scissor at first - It is missing the spring and is gumemd up and needs sharpening, but it is drilled to the LM´s pivot size and ground so it will lock. If you want to polish it up, I´ll send it over to you. PM me your address.
And thanks, guys. It was fun to mod it.
Sure, that would be great. Thanks a lot man
PM incoming. -
Just got the new Surge and had to change it up slightly to make it my ultimate HDMT...

CB
-
-
-
It counts!
live from Nate's mobile
-
-
-
New member here. Looks like I will be able to join this club soon. My wife was going to get me a new leatherman for my birthday since I’ve been carrying my Charge ALX for years. I went online to look at the new models, and nothing looked much better for what I need then the Charge that I already have.
As luck would have it I stumbled upon these forums and saw my first Re-Charge. I was hooked! The wire cutter on my Charge was all but useless. The only time I tried to use it, it didn’t cut very well and left a notch in the blade when it was done. The wife ordered me a Rebar last night for my project. I opted for BO, because I think the look of the black head with the black scales will look great.
So next week I’ll be taking the plunge into modding my Charge. First I’ll replace the head, but later I might try replacing the small screwdriver. I wanted that option back before I had Lasic. But now I never use the small driver. Do you guys know if the awl from the rebar will fit in its place, or is the awl too thick?
Thanks guys!
-
@Twiggz said:
New member here. Looks like I will be able to join this club soon. My wife was going to get me a new leatherman for my birthday since I’ve been carrying my Charge ALX for years. I went online to look at the new models, and nothing looked much better for what I need then the Charge that I already have.As luck would have it I stumbled upon these forums and saw my first Re-Charge. I was hooked! The wire cutter on my Charge was all but useless. The only time I tried to use it, it didn’t cut very well and left a notch in the blade when it was done. The wife ordered me a Rebar last night for my project. I opted for BO, because I think the look of the black head with the black scales will look great.
So next week I’ll be taking the plunge into modding my Charge. First I’ll replace the head, but later I might try replacing the small screwdriver. I wanted that option back before I had Lasic. But now I never use the small driver. Do you guys know if the awl from the rebar will fit in its place, or is the awl too thick?
Thanks guys!
Nice to have you with us.
The awl should fit in fine but for the handles to close you'll probably need to reprofile the awl a little.
More about it here. Looking forward to seeing what you do. -
I received my sacrificial BO Rebar today. I had hoped that the black oxide would have matched the black anodized scales better, but it still looks good IMO. It matches better in person, the BO sure doesn't photograph well. It might just be my phone.

Next I'm going to try swapping the awl from the Rebar with the micro driver on my ALX. I know I'll have to shave a little off the awl so it doesn't hit the rebar head. It also looks like it might be a hair thicker than the micro driver. I'll measure it with calipers before I start the swap.
-
Looks good.
live from Nate's mobile
-
-
-
-
Thanks to Matt, now I have my dream Leatherman: Mini-Surge
Wingman scissors ? Did they fit right in or was there a little grinding work ?
Swiss Army knives .
there's a little bit of grinding required. at a minimum, the pivot hole needs to be enlarged to fit the Wave/Charge pivot. when I modded my skinny Charge, I also had to make some slight adjustments to the locking face to get the liner lock to properly engage, but no such modification was needed on Kampfer's Mini-Surge.
-
Thanks to Matt, now I have my dream Leatherman: Mini-Surge
Wingman scissors ? Did they fit right in or was there a little grinding work ?
Swiss Army knives .
there's a little bit of grinding required. at a minimum, the pivot hole needs to be enlarged to fit the Wave/Charge pivot. when I modded my skinny Charge, I also had to make some slight adjustments to the locking face to get the liner lock to properly engage, but no such modification was needed on Kampfer's Mini-Surge.
Good deal, thanks for the info.
Swiss Army knives .
-
-
-
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




