Little Boy and Fat Man
-
I got to put Honestly John to the test this morning.
I ripped off half the wires for my trailers tail lights backing into some brush. I was getting a lawnmower.
he had me up and running in a few minutes.
I used the flat Phillips,stripper and flat driver. All worked flawlessly.
I'm kinda busy so I got to get back to it.
I just had to tell you it seen its first real use.
edit
I forgot to add the fat man was also used. It held the nuts while H.J. Turned the screws holding the light ti the frame.
-
Joel, I take it the snow has melted off up there in the great frozen north. :D
-
I'm going to put the Fat Man away in about a week and be using Little Boy for work and home
anybody got something on the Fat Man they would like me to test before I do.
I have already proven that it is a great work tool but I may have missed something.
another thought
the es4 I call H.J. Has been more than a useful part of my edc . He will be part of this review until its finished. I should have got one long ago. If this review has taught me anything its that the es4 is truly one of the best leatherman tools I've owned. I don't know how I got by without one.
-
-
Another unplanned test for the Fat Man.
I drove over him with my mini van at my works gravel parking lot.
no damage.
I thought it messed up the Bo coating but the scratches wiped off. The rock must have left them like chalk
-
Wow, Fat Man can take anything I'd say at this point :o
-
Why would you do something like that? :o How did that happen?
-
@Crow said:
Why would you do something like that? :o How did that happen?my van was running like crap this morning and I was messing around under the hood.
I used it to remove a few house clamps so I could inspect the Air Filter. It was very dirty so I replaced it and forgot the fat man under the hood.It must have feel out when I took it for a test drive. only the rear wheel drove over it but I may have drove over it again when I got back. It was pressed into the ground so I know I went over it at lest once. I noticed its absence when I was taken my lunch. I dump all my gear on my kitchen counter when I'm home . I drove like a mad man to go find it and it was just about where I was parked.
I think I got lucky. It was just laying on the ground for anyone to grab for a half hour or so.
-
Probably good it was a BO tool, wouldn't stick out as much. Really glad you didn't lose it!
-
I'm glad you found him. I'm sure fat man has sentimental value by now!
-
He sure does Steve. I'd be very upset if I lost him.
I learned something today
battery acid will remove black oxide coating.

I used my file yesterday on some battery connections cleaning them up.

-
Good to know.
-
Does it affect the functionality tho? Haha
Sent from my GT-I9300 using Tapatalk
-
Well I just put the fat man away and pulled out all my gear from the skinith.
I'm going to finish this review up using the little boy.
thoughts
I can do no more to the fat man to prove he's a great tool. Its been proven to me.

I prefer my st 300 to a swisstool but I prefer the Swisstool spirit to my rebar.
we will see if that changes after I use him more.
I'm going to ditch the ratchet, bits, and croc to lighten my edc. I was gifted a leatherman bit adaptor kit I will use in place of the ratchet and bits . I'm not sure what I will replace the croc with. A 4 inch crescent wrench or maybe a Gerber shard or something else. again we will see.
the es4 aka Honest John will be coming along. I like that little guy to much to leave him behind.the little boy will be working his butt off this summer. I'm not sure if he's up to it or not.
Only one way to know for sure.
-
I look forward to the summer of the little boy :D
-
I look forward to the summer of the little boy :D
it should be interesting.
I think I am going to break it.
I normally wouldn't take this small of a tool to work.
That's why it'll be interesting ;) I'm curious if it'll be able to handle your daily work. I'm looking forward to it for sure...heck, I'm looking forward to summer period ;)
-
I look forward to the summer of the little boy :D
it should be interesting.
I think I am going to break it.
I normally wouldn't take this small of a tool to work.
That's why it'll be interesting ;) I'm curious if it'll be able to handle your daily work. I'm looking forward to it for sure...heck, I'm looking forward to summer period ;)
I love the Rebar but it remains to be seen if it can handle the abuse. It's a lot smaller and I fear its implements may not hold up to as much stress.

-
If its anything like a wave, I bet it will make it just fine.
live from Nate's mobile
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
