Sheffield Crocodile
-
Well here's the whole famn damily (I think?) all together at last:

Kershaw A100 Multi-Tool, the original
Craftsman 45516. Made by Kershaw and identical to the A100, except for misc logo differences stamped on the handle.
Sheffield Crocodile, variation A. Note pregnant lower handle and curvy plier jaws. Knife blade moved from one-hand opening position in the upper handle, to 2HO position in the lower handle. No saw blade.
Sheffield Crocodile, variation B. Note pliers and handles more faithfully copy the Kershaw than variation A. Scissors instead of a saw blade.
Cummins Multi-Purpose Pliers. Generic made-in-China construction. Poor quality and workmanship throughout. No saw, no inch or metric rulers. -
@J-sews said:

Sheffield Crocodile, variation A. Note pregnant lower handle and curvy plier jaws. Knife blade moved from one-hand opening position in the upper handle, to 2HO position in the lower handle. No saw blade.
Sheffield Crocodile, variation B. Note pliers and handles more faithfully copy the Kershaw than variation A. Scissors instead of a saw blade.Necro thread revival.
Does anyone know the Sheffield model number for Sheffield Crocodile variation B ?
I know variation A is 12025, but haven't been able to find it for the variation B. I'm hoping if I get the number it might help me find one. Variation A is much easier to find, but the B is much more elusive (in fact MTo is the only place I've ever seen them mentioned).
-
I just checked my notes Greg, but I don't have anything mentioned about the model number. And unfortunately, I'm not living in the same house as my collection is right now, so I can't check the tool itself. :-\
I'll try to find out in the next few days and let you know.

EDIT: Unless Dan or Terry can check theirs first...?
-
@J-sews said:
I just checked my notes Greg, but I don't have anything mentioned about the model number. And unfortunately, I'm not living in the same house as my collection is right now, so I can't check the tool itself. :-\I'll try to find out in the next few days and let you know.

EDIT: Unless Dan or Terry can check theirs first...?
Thanks Bob. I'm not sure if it is stamped on the tool itself or not. If it isn't then I'll hope someone has one still in the clampack. With the Sheffield tools the seller sometimes list them by model number (that's how I found the large slip-joint pliers and I'm currently on the trail of the Schrade ST1 sort-of-copy), so if I can get the model number that might help me find one (then I will be able to focus on looking for the Bulit and Cummins copies).
-
Well as far as Crocodiles go, I only have two versiona of type A. One has Pat Pending on it, the other which is a later version doesn't. The Pat Pending has no numbers. The other however does : 12025 Pat. No. D455, 629.
So I can't help you. I haven't been able to find a type B yet...and I have been looking.
-
@Chako said:
Well as far as Crocodiles go, I only have two versiona of type A. One has Pat Pending on it, the other which is a later version doesn't. The Pat Pending has no numbers. The other however does : 12025 Pat. No. D455, 629.So I can't help you. I haven't been able to find a type B yet...and I have been looking.
Snap ! I have those same two versions of type A, and I've also been looking for a type B for quite a while .... with the exact same lack of success :(
Maybe we better start a buyers cartel now, so if we ever find one we don't both bid it up to a silly price

-
To be truthful, I have slowed down quite a bit in my collecting. I think I have reached my critical mass to space ratio. This means I can still collect, but a lot slower. That and I don't need every single model and variation ever produced...ah well...at least for non Leathermans.
-
I can't tell from the photos. Does the Sheffield Crocodile have a huge spacer next to the lower jaw to ensure the lower jaw aligns correctly? Mine does, but these photos seem to indicate some don't?
-
@Yadda said:
I can't tell from the photos. **Does the Sheffield Crocodile have a huge spacer next to the lower jaw to ensure the lower jaw aligns correctly? ** Mine does, but these photos seem to indicate some don't?Both my Sheffields have this thick washer, as do all of my genuine Kershaws and the Craftsman re-labelled tools.
-
Good. I thought maybe mine was deformed. :D
-
I just got one of the Sheffield versions with the OHO blade. It arrived in beat down horrible condition. I had to replace the lower handle pivot with one out of a POS kobalt MT, and then the handles aligned properly and the tool was usable. I had to disassemble the tools to fix the backspring/lock because it was bent outwards and didn’t stop the tools from over-extending. All that hardware LOOKS like Leatherman screws, but some of them are rivets that once separated, never again shall stay together. So I need to machine down another kobalt pivot to length to replace that.
The one I received was completely clapped out and I’ve made it usable... but it doesn’t strike me as a quality tool. The Sheffield 12020 is a quality tool. This crocodile thingy feels like a cheap harbor freight vise grip with some tools thrown in the handle. The wire cutters aren’t even sharpened.
I am disappointed. It wasn’t really very cheap either. $30 for a broken tool, plus some free kobalt parts and a couple hours of my time :/
Oh and it needs a new spring for the scissors to boot. Sigh.
Also it’s a LOT smaller than I envisioned.
Charles.
-
Okay, so I was a little harsh because I was really disappointed in how used up this tool was.
But, I spent some time actually fixing it correctly. The lower pivot screw I replaced was a little too long, resulting in some unacceptable play. Fortuntely I had some shims, and I shimmed it up and the play is gone. I removed the OEM style rivets and just used some 3mm stainless rod and peened the ends to make a new tool pivot. I sharpened the wire cutters, and they work on speaker wire and zip ties. 12ga stranded is still not doable, but it'll cut romex all day. With everything repaired and adjusted... it's still not the same quality as the Sheffield 12020. The tools are close, but the vise grip is really the disappointment here. It's not not a precision-made part. Playing with this tool just makes me want a Crunch all the more.
Charles.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login