Need Input on Climber.
-
@ToolJoe said:
..I have a love/hate relationship with the Skeletool and have an urge to give an SAK another shot.I understand the hate part. The Skeletool wieghts 5oz which is the same as a SOG Pocketpower plier or a LM PST, and just 2 ounces short of most pliers-based MTs. The Skeletool's weight-to-tool ratio is poor.
So then you try to add a SAK (4-5 ounces) to the Skeletool (5 ounces) and now you're packing 9-10 ounces of weight, which is the same weight of a Supertool 300. You might as well carry the Supertool. Or carry a Wave or Spirit at 7 ounces, and have a better set of tools than you would with 10 ounces of Skeletool & SAK.
So again, the Skeletool isn't worth it because of the weight-to-tool ratio. Why even carry the thing?
-
@Lynn LeFey said:
I have had the Leatherman Micra, the SOG Crosscut, and 3 copies of the Vic Climber. The scissors on the vic are great, but are for ONLY light duty cutting. I accidentally snipped a bread twisty-tie with the vic scissors and badly notched the scissor blade. This is a feat that either the Micra or Crosscut do without any damage or difficulty.I just used the scissors of a climber to cut a bread twisty tie into about 8 pieces. The scissor blades came out undamaged.

-
@shamus said:
@Lynn LeFey said:
I have had the Leatherman Micra, the SOG Crosscut, and 3 copies of the Vic Climber. The scissors on the vic are great, but are for ONLY light duty cutting. I accidentally snipped a bread twisty-tie with the vic scissors and badly notched the scissor blade. This is a feat that either the Micra or Crosscut do without any damage or difficulty.
I just used the scissors of a climber to cut a bread twisty tie into about 8 pieces. The scissor blades came out undamaged.

Sounds like you got lucky!
-
I use EDC scissors primarily for skin boo boos, threads, etc., so for me the precision of Victorinox scissors prevails over the heavier duty Leatherman scissors.
-
I've had good luck with the scissors too apparently, I haven't had to sharpen any that I had from new, but I have had to sharpen used ones, if not abused, they are fairly tough.
@nate j said:
If you still want pliers for light duty work and scissors go for the deluxe climber or deluxe tinker. Buy that adds a 4th layer. Not sure how the pliers are on SAKs as my 91mm Mechanic hasn't arrived yet. Maybe somebody with SAK pliers could advise?
With regard to fit, finish, and functionality, the SAK pliers are on par with other Vic tools, which is to say very good. However, it should be noted that they are on the small/light duty side as far as pliers go.
The 91mm pliers are amazing, I have used/abused them in all sorts of ways and they are very durable and functional, but the SwissTool pliers are much more capable. The main benefit of the 91mm pliers for me, is that I don't need to carry them in a sheath, the Mechanic and Deluxe models are easily pocketable.

-
@DazMechanical said:
If you still want pliers for light duty work and scissors go for the deluxe climber or deluxe tinker. Buy that adds a 4th layer. Not sure how the pliers are on SAKs as my 91mm Mechanic hasn't arrived yet. Maybe somebody with SAK pliers could advise?I have a deluxe Climber. For small projects the pliers is great but it's a very thick layer making it a little to big to edc for my taste. But if I'm going somewhere I think I'll need it (like I did last week) It was a life saver.(pulling nails out of walls disassembling cheap furniture ect.)
-
I am carrying a camo Climber today but forgot about this one!

-
@powernoodle said:
I use EDC scissors primarily for skin boo boos, threads, etc., so for me the precision of Victorinox scissors prevails over the heavier duty Leatherman scissors.It's difficult to say one is better than the other. Vic scissors will cut my fingernails while the Micra's will not do so nearly as neatly. But then LM scissors are good for heavier cutting.

-
If you still want pliers for light duty work and scissors go for the deluxe climber or deluxe tinker. Buy that adds a 4th layer. Not sure how the pliers are on SAKs as my 91mm Mechanic hasn't arrived yet. Maybe somebody with SAK pliers could advise?
I have a deluxe Climber. For small projects the pliers is great but it's a very thick layer making it a little to big to edc for my taste. But if I'm going somewhere I think I'll need it (like I did last week) It was a life saver.(pulling nails out of walls disassembling cheap furniture ect.)
I've been carrying both a Rebar and a Swiss Champ recently and don't find it to be too much at all. The plier layer on the SC only adds a tiny bit more thickness, IMO.
-
If you still want pliers for light duty work and scissors go for the deluxe climber or deluxe tinker. Buy that adds a 4th layer. Not sure how the pliers are on SAKs as my 91mm Mechanic hasn't arrived yet. Maybe somebody with SAK pliers could advise?
I have a deluxe Climber. For small projects the pliers is great but it's a very thick layer making it a little to big to edc for my taste. But if I'm going somewhere I think I'll need it (like I did last week) It was a life saver.(pulling nails out of walls disassembling cheap furniture ect.)
I've been carrying both a Rebar and a Swiss Champ recently and don't find it to be too much at all. The plier layer on the SC only adds a tiny bit more thickness, IMO.
Me personally I'm not a Solder or a Cop any more. No more body armor M4's or Mp5's or batman utility belt if it's don't fit with comfort in my pocket it stays in the Jeep. It' just where I'm at in life these days.
-
A Mountaineer would be an even better companion to a pair of pliers for EDC, IMO.
-
If you still want pliers for light duty work and scissors go for the deluxe climber or deluxe tinker. Buy that adds a 4th layer. Not sure how the pliers are on SAKs as my 91mm Mechanic hasn't arrived yet. Maybe somebody with SAK pliers could advise?
I have a deluxe Climber. For small projects the pliers is great but it's a very thick layer making it a little to big to edc for my taste. But if I'm going somewhere I think I'll need it (like I did last week) It was a life saver.(pulling nails out of walls disassembling cheap furniture ect.)
I've been carrying both a Rebar and a Swiss Champ recently and don't find it to be too much at all. The plier layer on the SC only adds a tiny bit more thickness, IMO.
Me personally I'm not a Solder or a Cop any more. No more body armor M4's or Mp5's or batman utility belt if it's don't fit with comfort in my pocket it stays in the Jeep. It' just where I'm at in life these days.
I can understand that

-
I am carrying a camo Climber today but forgot about this one!

That's a beautiful Climber.
Thanks Gene! As an older LNF version, it lives in the SAK collection box....I never carry it.
I do look forward to the pics you post. You have some very kool knives and great photo skills.
-
I am carrying a camo Climber today but forgot about this one!

That's a beautiful Climber.
Thanks Gene! As an older LNF version, it lives in the SAK collection box....I never carry it.
I do look forward to the pics you post. You have some very kool knives and great photo skills.
Gosh Gene, thank you!

-
Is there any downsides to the climber eco, other than the sides being a cheaper material, ive read that all the rest of the parts are the same quality. It seems to be half the price. Any thoughts? :tool:
-
I prefer the nylon Eco scales to the Cellidor ones- the matte texture grips better, and nylon is a really strong material.
Supposedly the quality control is different- Vic inspect every single one of the normal line, but only every tenth eco model- but they still carry the same guarantee. -
@?eter said:
I prefer the nylon Eco scales to the Cellidor ones- the matte texture grips better, and nylon is a really strong material.
Supposedly the quality control is different- Vic inspect every single one of the normal line, but only every tenth eco model- but they still carry the same guarantee.The problem nobody seems to be pointing out with the Eco nylon scales is they do not include a hole for the PIN ...
-
I think I've maybe needed a pin twice ever when I wasn't at home. And, since the nylon scales are fairly soft, I'm not certain the pin hole would work as well, loosening up and letting the pin fall out. And if that's NOT the case, I'd think carving the pin hole in would be a fairly simple matter.
The nylon scales are VERY forgiving about being removed and replaced. I've had celidor scales that... weren't. The edges around the holes that engage the pins would break and the scales would become loose.
While this is my experience, understand I have VERY little experience with the matter, so weigh my opinion accordingly.
If you're looking for a good budget tool, I think an eco model is excellent.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login