Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Squirt modification

Scheduled Pinned Locked Moved The Mod Squad
59 Posts 1 Posters 11.0k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Squirt modification
Squirt modification
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • kent ct Offline
    kent ct
    Posts: 125
    kent ct Offline
    kent ct
    wrote on last edited by
    #33 Quote Reply

      @zepla said:
      Are you kidding me, send something over? :cheers: That sounds great!

      But before I ask something like that I'll check out our office supplies first and see if I can make something work myself. And meassure that pin hole exactly, or are you sure that it is the 3.2 mm I think it is?

      Measure the old pin, not the hole. Much harder to measure a hole accurately. If you have a micrometer the exact measurement is 3.175mm or .125 thousands. I am 90 percent certain it is 1/8 inch.

      Richard

      1 Reply Last reply
      • zepla Offline
        zepla
        Posts: 1,053
        zepla Offline
        zepla
        wrote on last edited by
        #34 Quote Reply

          @kent ct said:

          @zepla said:

          ... Another thought. How about 1/8 dowel pins. Easy to soften so you can file. Two ten thousands over size so can make a tight very strong pivot. For the ends, two brass bushings which can be riveted into or just Loctite in the bushing. I have spring steel .025 or .63 mm. a bit under 10mm wide, very strong. If you would like to try this I will make the brass bushings and mail you a piece of spring steel the length you need along with the dowel pins which I will soften. Email me if you want to try.

          I did some measurements, and it looks like you're right al along! It is indeed the 3.2mm you thought it would be :salute:

          I looked in every corner of my office and couldn't find enything usefull. It looks like that I'll have to take your offer :D A :mail: is comming your way...

          1 Reply Last reply
          • kent ct Offline
            kent ct
            Posts: 125
            kent ct Offline
            kent ct
            wrote on last edited by
            #35 Quote Reply

              @zepla said:

              @kent ct said:

              @zepla said:

              ... Another thought. How about 1/8 dowel pins. Easy to soften so you can file. Two ten thousands over size so can make a tight very strong pivot. For the ends, two brass bushings which can be riveted into or just Loctite in the bushing. I have spring steel .025 or .63 mm. a bit under 10mm wide, very strong. If you would like to try this I will make the brass bushings and mail you a piece of spring steel the length you need along with the dowel pins which I will soften. Email me if you want to try.

              I did some measurements, and it looks like you're right al along! It is indeed the 3.2mm you thought it would be :salute:

              I looked in every corner of my office and couldn't find enything usefull. It looks like that I'll have to take your offer :D A :mail: is comming your way...

              Check your mail

              Richard

              1 Reply Last reply
              • zepla Offline
                zepla
                Posts: 1,053
                zepla Offline
                zepla
                wrote on last edited by
                #36 Quote Reply

                  Here's a little update of my squirt mod.

                  I have contact with Kent, he is going to send me some parts needed for this mod :cheers: And I've contact with Marc, from EDC Depot for a new squirt and Spyderco Ladybug. My plans are to make a proto with the squirt and ladybug that I already have (you've seen the pictures) and if everything goes well I'll make a new one with out all the screwing up I did on this one :D

                  Now I'm just waiting for the parts and making plans in my head to make this work. I'll keep you all posted :)

                  1 Reply Last reply
                  • J-sews Offline
                    J-sews
                    Admin Team
                    Posts: 23,224
                    J-sews Offline
                    J-sews
                    Admin Team
                    wrote on last edited by
                    #37 Quote Reply

                      Looking forward to hearing more from you zepla :)

                      1 Reply Last reply
                      • zepla Offline
                        zepla
                        Posts: 1,053
                        zepla Offline
                        zepla
                        wrote on last edited by
                        #38 Quote Reply

                          Yet an other small update of my squirt mod.

                          The parts from Kent are in :cheers: Now I have to figure out how the use them. Of course he explained it perfect, it just my idiot brain that is the problem in this equation :-[

                          I'm going to experiment with this and try some designs I came up with. I'm sure I have something to show for it in a few days. (I do have to work some times and spend some time with the girlfriend in between this important project :D )

                          To be continued....

                          1 Reply Last reply
                          • J-sews Offline
                            J-sews
                            Admin Team
                            Posts: 23,224
                            J-sews Offline
                            J-sews
                            Admin Team
                            wrote on last edited by
                            #39 Quote Reply

                              @zepla said:
                              Yet an other small update of my squirt mod.

                              The parts from Kent are in :cheers: Now I have to figure out how the use them. Of course he explained it perfect, it just my idiot brain that is the problem in this equation :-[

                              I'm going to experiment with this and try some designs I came up with. I'm sure I have something to show for it in a few days. (I do have to work some times and spend some time with the girlfriend in between this important project :D )

                              To be continued....

                              I hate it when women and work get in the way of important business! >:( ;) :D

                              1 Reply Last reply
                              • zepla Offline
                                zepla
                                Posts: 1,053
                                zepla Offline
                                zepla
                                wrote on last edited by
                                #40 Quote Reply

                                  They never seem to understand my priorities :D

                                  1 Reply Last reply
                                  • zepla Offline
                                    zepla
                                    Posts: 1,053
                                    zepla Offline
                                    zepla
                                    wrote on last edited by
                                    #41 Quote Reply

                                      Getting on the way but missing a small drill bit now. Broke all the small ones when trying to make a hole in the springsteel I got from Kent. To bad the shopes are closed now and now my little project is on a hold.

                                      Notice the mess I've made by just fiddling about with a squirt. Imagine what I can do with a larger tool :D

                                      Oh, and just onother thing I would like to mention. I ordered some stuff by edcdepot and payed for it already. Today I recieved a mail from Marc that I get some money back due to a change in shipping costs. And that the package is on its way. :salute: for Marc, a honest guy running a honest shop. I have to say, that's rearly found on the internet these days!

                                      P1000169.JPG

                                      1 Reply Last reply
                                      • kent ct Offline
                                        kent ct
                                        Posts: 125
                                        kent ct Offline
                                        kent ct
                                        wrote on last edited by
                                        #42 Quote Reply

                                          You need slow speed to drill steel. Can not be done with Dremel unless you use carbide bit. Why not soften steel? You can then do all your shaping and when done re-harden and temper.

                                          Richard

                                          1 Reply Last reply
                                          • Benner Offline
                                            Benner
                                            Posts: 28,081
                                            Benner Offline
                                            Benner
                                            wrote on last edited by
                                            #43 Quote Reply

                                              Guys like Marc are a rarity these days.

                                              1 Reply Last reply
                                              • Tarrodemierda Offline
                                                Tarrodemierda
                                                Posts: 3,699
                                                Tarrodemierda Offline
                                                Tarrodemierda
                                                wrote on last edited by
                                                #44 Quote Reply

                                                  bit off topic,sorry:

                                                  hey zepla,whats that little tolkit u have there with wrenc,sockets,bits etc?

                                                  looks delicious.

                                                  SO,where to get a hold of those ?

                                                  1 Reply Last reply
                                                  • zepla Offline
                                                    zepla
                                                    Posts: 1,053
                                                    zepla Offline
                                                    zepla
                                                    wrote on last edited by
                                                    #45 Quote Reply

                                                      That's a Teng Tool set. (www.tengtools.com) They make excellent tools for reasonable prices and have exactly what I need, like that set you see at the pictures. It is very small but has just what I regulary need for my work. Most of my other tools are from Teng as well. An even smaller set and a bigger set. (no, I don't have stock options in that company ::) )

                                                      Funny thing was the first time I had seen this stuff I tought it was just chinees made crap. What did you expect with a name like that :think: But when I looked closer it looked quit good to my surprise. I did some research and now I know it isn't chinees and comes with a sort of lifetime warrenty and if I need some tool I'll buy Teng. (It helps when you have Teng dealer around the corner in my case.)

                                                      1 Reply Last reply
                                                      • Tarrodemierda Offline
                                                        Tarrodemierda
                                                        Posts: 3,699
                                                        Tarrodemierda Offline
                                                        Tarrodemierda
                                                        wrote on last edited by
                                                        #46 Quote Reply

                                                          oh its a teng? im familiar to them,at fisrt when i saw your pic i looked at that mini ratchet that looked like ones teng sells.they dont sell tengs here,do u know one in uk(us who sells em ,maybe even overseas.

                                                          ive seen those in sweden,just couple weeks ago while i was on large motorcycle happening,teng had a small....tent there and they had set that held some 5 sockets,that ratchet,and some bits,intended for motorcycle use.i looked at that sam kit at 2007 too,but that happening is sooo hot and i have to get lots of beer to avoid dehydration ;),and that stuff eats my wallet.

                                                          1 Reply Last reply
                                                          • jzmtl Offline
                                                            jzmtl
                                                            Posts: 8,551
                                                            jzmtl Offline
                                                            jzmtl
                                                            wrote on last edited by
                                                            #47 Quote Reply

                                                              @kent ct said:
                                                              You need slow speed to drill steel. Can not be done with Dremel unless you use carbide bit. Why not soften steel? You can then do all your shaping and when done re-harden and temper.

                                                              Richard

                                                              I think harden and temper steel is a bit beyond us ordinary folks. :o

                                                              1 Reply Last reply
                                                              • scibeer Offline
                                                                scibeer
                                                                Posts: 427
                                                                scibeer Offline
                                                                scibeer
                                                                wrote on last edited by
                                                                #48 Quote Reply

                                                                  You can try spot anealing the area you want to drill with a soldering iron. I've done it before with marginal results. I was able to drill a hole with a cobalt bit, but the bit was history afterward.

                                                                  A carbide bit is about the only equalizer for hardened steel. pm me and I can help you get a few for a lot less than the normal $15 or so each.

                                                                  1 Reply Last reply
                                                                  • zepla Offline
                                                                    zepla
                                                                    Posts: 1,053
                                                                    zepla Offline
                                                                    zepla
                                                                    wrote on last edited by
                                                                    #49 Quote Reply

                                                                      @ Tarrodemierda, I have that smaller set you mentioned as well. Very handy little set!

                                                                      @ Scibeer, at the moment I just need to drill a hole in a piece of spring steel. It is less than 1mm or so thick. With a normal drill I should go through it, I guess. I just have nothing in the house at the moment. That will be sorted today or at least this week. But thanks for the offer to help anyway! :cheers:

                                                                      The really big problem will be drilling a hole in the spyderco knife that is comming my way. That is thick and really hard! The hole I've made in the current spyderco blade took me twee weeks!

                                                                      1 Reply Last reply
                                                                      • scibeer Offline
                                                                        scibeer
                                                                        Posts: 427
                                                                        scibeer Offline
                                                                        scibeer
                                                                        wrote on last edited by
                                                                        #50 Quote Reply

                                                                          It's not soft stuff, is it?

                                                                          I have a great collection of burnt up drill bits being used as punches!

                                                                          1 Reply Last reply
                                                                          • kent ct Offline
                                                                            kent ct
                                                                            Posts: 125
                                                                            kent ct Offline
                                                                            kent ct
                                                                            wrote on last edited by
                                                                            #51 Quote Reply

                                                                              @jzmtl said:

                                                                              @kent ct said:

                                                                              You need slow speed to drill steel. Can not be done with Dremel unless you use carbide bit. Why not soften steel? You can then do all your shaping and when done re-harden and temper.

                                                                              Richard

                                                                              I think harden and temper steel is a bit beyond us ordinary folks. :o

                                                                              We are only talking about a small piece of high carbon spring steel of uniform thickness. It only gets tricky when the steel is not uniform in shape. Also this is not stainless steel which work hardens if not drilled carefully. Another approach to putting a hole in spring steel is to put the steel on a piece of wood and center punch it where you want the hole. this will make a dimple in the steel. Turn it over and file the projecting dimple off. You will be left with a small hole that you can follow up with the drill. The drill will bite much more easily. Also drill with the spring on a piece of wood and clamped down to avoid it spinning around when the drill breaks through.

                                                                              To open the tang hole on a blade you might consider honing it open if if does not need very much. Valve grinding compound and copper or brass as a hone.

                                                                              Richard

                                                                              1 Reply Last reply
                                                                              • zepla Offline
                                                                                zepla
                                                                                Posts: 1,053
                                                                                zepla Offline
                                                                                zepla
                                                                                wrote on last edited by
                                                                                #52 Quote Reply

                                                                                  The center punch approach sound like a good idea! Once you have a little hole or even a dimple drilling would be much easier indeed.

                                                                                  And making a hole in a blade just a bit bigger is not so difficult with the dremel (not even for me :D). But making a new hole is a problem in my experience :ahhh I went with the balde I have now to a blacksmith and even he couldn't make a hole in it! I'm not looking forward to go over that procedure all over again. That VG-10 steel is really, really tough! Why oh why does my squirt not come standard with a proper knife ::)

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Squirt modification
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0