Vic knife sharpener question
-
My Dad used these carbide sharpeners for years on his work knives and it you push too hard, it will remove too much metal and the blades will start losing their original profile. You can actually see the metal peeling off on very blunt/dull blades.
I use these kinds of sharpeners on very dull or abused blades. I cut a new bevel with them and then finish it by hand. Some stuff I buy used is so dull you can overly wear a nice diamond stone/steel before you get it thinned out. I have an old extra coarse DMT Diafold sharpener this happened to.
They are ok but only with very light pressure and very few strokes as they will eventually "use a blade up" if used improperly and too often.
-
I like many other don't recommend those carbide sharpeners. Weather it's Victorinox or not. They don't give a consistent edge and they remove a lot of material.
I recommend a sharpening system like this...
http://www.amazon.com/Lansky-Deluxe-5-Stone-Sharpening-System/dp/B000B8IEA4/ref=cm_cr_pr_sims_t
http://www.amazon.com/Frost-Blademaster-Standard-Knife-Sharpening/dp/B0090UTF3O/ref=sr_1_6?ie=UTF8&qid=1401203558&sr=8-6&keywords=blademaster+sharpeneror a proper whetstone if your able to use that method...unfortunately I am not. Couldn't use a stone if my life depended on it.
-
@SAK Guy said:
My Dad used these carbide sharpeners for years on his work knives and it you push too hard, it will remove too much metal and the blades will start losing their original profile. You can actually see the metal peeling off on very blunt/dull blades.I use these kinds of sharpeners on very dull or abused blades. I cut a new bevel with them and then finish it by hand. Some stuff I buy used is so dull you can overly wear a nice diamond stone/steel before you get it thinned out. I have an old extra coarse DMT Diafold sharpener this happened to.
They are ok but only with very light pressure and very few strokes as they will eventually "use a blade up" if used improperly and too often.
I could not agree more these kind of sharpeners well turn a knife into an awl in no time if you use it all the time. I prefer a very old butcher steel to keep my knifes sharp. If you do it right most people cant see the blade has been sharpened till they they check it and it's a very smooth shaving sharp not at all jagged.
-
@Fattsgalore said:
I like many other don't recommend those carbide sharpeners. Weather it's Victorinox or not. They don't give a consistent edge and they remove a lot of material.I recommend a sharpening system like this...
http://www.amazon.com/Lansky-Deluxe-5-Stone-Sharpening-System/dp/B000B8IEA4/ref=cm_cr_pr_sims_t
http://www.amazon.com/Frost-Blademaster-Standard-Knife-Sharpening/dp/B0090UTF3O/ref=sr_1_6?ie=UTF8&qid=1401203558&sr=8-6&keywords=blademaster+sharpeneror a proper whetstone if your able to use that method...unfortunately I am not. Couldn't use a stone if my life depended on it.
Sharpeners like those work very well on most knifes like your SAK's but you can't use them on thicker bladed knifes like a K bar BK2 or cold steel SRK you can't get the angel right and you can ruin a good blade but for a thiner blade like a SAK they work very well.
-
This one does every angle from 10-24 degrees.
-
If you are really into sharpening, I also recommend the Wicked Edge. It has now offered a lower angle adapter clamp, which will bring the angle down to 8 to 10 deg. The good thing is if you can find a 'right' setting for your knife, you can pretty much for sure repeat the result without any human error.
Here's a comparison video done by a blade person:
https://www.youtube.com/watch?v=SGo3pKhp6L8But personally, as I have said earlier, I still recommend Spyderco Sharpmaker, easy and painless, also minimum setup effort.
-
If you freehand the Fallkniven stones work really well IMO.
The DC-4 combo is the daily "touch up" stone in my bag...

-
-
If you freehand the Fallkniven stones work really well IMO.
The DC-4 combo is the daily "touch up" stone in my bag...

+1 for the DC-4

Seems a DC-3 to me :D
Very good to keep in a bag in case you want to sharpen in the field.
On the other hand, I actually prefer to keep it in the drawer, so I can use it's sheath to keep my alox from getting all scratched up. It's a perfect fit. -
My pic's a DC-4 but I have DC-3's in sheath pockets and the Big 8"Bench stone...they are all great.
Here's some of mine:
-
I was always proud of my ability with a 6 or 8" bench stone and have a Lansky set around here somewhere, but use the Spyderco Sharpmaker 99% of the time and recommend it highly. I think anyone can get a good edge with one.
-
That look to me a pretty good knife sharpener.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login