Little Boy and Fat Man
-
I'll have to have the forum printed out at work.
all I got for net is a cell phone.
I do have a back up rebar I was gifted from a good friend.
I'm not going break it at work.
there's no reason to break two.
also its like new and I want to keep it that way >:D
-
Maybe this is a sign that its time for the MP600. Plus, Mrs. Powernoodle is sitting right next to me at the kitchen table reading a book called Necessary Endings: The Employees, Businesses, and Relationships that All of Us Have to Give Up in Order to Move Forward.
-
I said I was going 6 months when I started this topic.
I'm not going to cut it short.
Il be using my back up rebar at home and bring the st300 to work until the end of the month.
I'm thinking that the rebar doesn't belong on the job site. Its much more suited to my off work needs.
its kinda my fault it broke because I knew if I used it at work it would.
-
Ps
I still think that the rebar is a good tool.
I shouldn't have brought it to work.
its the wrong tool for my job.
if I would have be using the st300 much larger flat head driver this would not have happened.
-
Maybe you are being too hard on yourself. You said you weren't using very much force. Sounds like there was something wrong with the driver - maybe a stress fracture or whatever - and not something wrong with the operator. You were just using the Rebar for its intended purpose.
-
@powernoodle said:
Maybe you are being too hard on yourself. You said you weren't using very much force. Sounds like there was something wrong with the driver - maybe a stress fracture or whatever - and not something wrong with the operator. You were just using the Rebar for its intended purpose.maybe
but I know I shouldn't have been using it at work in the first place.
-
That's a bummer Joel :( Still, I feel that the Rebar survived a lot of work and whatnot, so as you said, it's a good tool. It's odd how sometimes the simplest, innocent uses end up breaking the tool, even after it's been put through more strenuous work. I don't remember how much you used the driver, but maybe this was a cumulative issue over several uses and it just finally snapped
Who knows for sure, but it's too bad it didn't make it until the very end. -
Yeah I'm still a little disappointed it didn't make it the last couple weeks Kyle.
I unwired a lot of homes with the same driver. Some of the screws I had to use two hands to get moving. Its odd to me that it broke when I was just holding a screw.
it was a odd angle. Maybe I used some force I never applied before.
good thing its not my only tool. :)
-
The bright side.
I get to make leathermans warranty a part of this review.
I'm going to get the warranty crap printed off tomorrow or Friday..
I got a stuck trailer home I got ti deal with so I won't be around the office.
-
Sad news JA! When you send Little Boy in,remember marking him as being sentimental value! That way you'll get him back,rather than having him replaced
-
You did say you'd break it

Maybe a stress fracture/crack occurred at some point, and this light use was all it took to break it.
Still, it did very well considering what hes been trough so far. -
these things happen and you showed the whole thing, even the ugly side of it all. so kudos to you
-
Was that the one that was lost and buried in snow for a couple of months this winter?
Maybe some rust did develop inside the pivot area and weakened it.
It does look like a break under torque by the looks of that pic.
-
thanks guys
and no I don't think rust had anything to do with the break. It broke at the pivot . It was still oily there when I found him.
I'm getting ready to head out to work and I'm putting fat man on my belt.
I forgot how much heavier he is.
-
I wasn't at work long before I needed the fat man
I had a lose connection I needed to tighten up on a battery to get a old truck up and running.
the new truck is stuck were it is until it dries up and we can finish moving the house.

-
Its raining.
I'm working inside on installing a new tub and shower in a used mobile home that's on our lot for sale.
I've been using the fat man to remove all the old fixtures and get ready for new.
I appreciate the extra length of its tools especially the saw.

it only took a few strokes to cut through the PVC water pipe.
-
It was like working with a old friend today.
I think I missed using fat man alot more than I thought.
I know now its my favorite work tool.
-
That's cool Joel-it definitely looks like a beast

-
I can understand the sentimentality. I get quite attached to some of my MT's and SAK's as well.

-
Fat Man will be the tool I judge all other tools by.
he's the best multitool I've ever used.
we going to try move that home we left Wed.
wish me luck.
I need it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login