Stainless Huntsman
-
I think I'm going to have to scrap the scales. :( I was a bit overzealous shaping the edges and they're smaller than the springs and liners now. I also don't like the way the Phillips works - would have been better if I'd gone for a Phillips opposite the can opener and cap lifter. To make matters worse, instead of using threaded barrel pins I decided to peen the rivets - left too much material on and now it's too tight. Ah well, every day is a school day.
-
Gutted. You were doing so well. Better to do over and be happy than make do and be left wanting.
-
Yeah, this one was for a friend (who has been waiting very patiently for me to finish it) so had to be right.
-
Right, back on it. Stainless Huntsman is now a G10 Fieldmaster.
<a href="https://flic.kr/p/owRNox" target="_blank" rel="noopener noreferrer"><img src="https://farm6.staticflickr.com/5562/14789060315_456d66c6c9_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
G10 scales drilled, cut and sanded - gone for a matt finish which actually looks really nice. Much easier to work than the stainless - fast to sand but rather smelly. Drilled out the backside phillips and the can opener and did a trial fit. Everything works fine but I need to make some brass washers to go between the tools and the scales. I also need to make the barrel pins - I've managed to source some 3mm OD x 1.6mm ID stainless tubing so hopefully I can just tap it out to M2 for the screws. -
The stainless tube worked really well for the pivots:
<a href="https://www.flickr.com/photos/26008756@N08/14801344091/" target="_blank" rel="noopener noreferrer"><img src="https://farm3.staticflickr.com/2923/14801344091_e564eb0af6_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Might not look like much but I don't need to drill them out, just cut to length, clean the ends and tap to M2 for the screws.Not everything went to plan though:
<a href="https://www.flickr.com/photos/26008756@N08/14781458816/" target="_blank" rel="noopener noreferrer"><img src="https://farm3.staticflickr.com/2902/14781458816_6650e1dee9_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Need to work on my technique for making brass washers. -
@hiraethus said:
Right, back on it. Stainless Huntsman is now a G10 Fieldmaster.G10 scales drilled, cut and sanded - gone for a matt finish which actually looks really nice. Much easier to work than the stainless -** fast to sand but rather smelly**.
You should wear a dust mask when sanding CF and preferably sand it wet to keep the dust down even more. BAD stuff to get in your lungs.
-
Yep, dust mask for sure. I'll try wetting it next time too.

-
Finished:
<a href="https://flic.kr/p/oCjWQL" target="_blank" rel="noopener noreferrer"><img src="https://farm4.staticflickr.com/3854/14850939252_477d785988_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a><a href="https://flic.kr/p/oC5XoM" target="_blank" rel="noopener noreferrer"><img src="https://farm4.staticflickr.com/3905/14848209541_65fc3516ac_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
<a href="https://flic.kr/p/oAjRuG" target="_blank" rel="noopener noreferrer"><img src="https://farm4.staticflickr.com/3896/14828288276_9dc2a3199e_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Not quite what I expected when I started, but I'm happy with the result. If I'd known I was going to peen the scales on I wouldn't have drilled everything to 3mm, but I couldn't get the stainless barrel pins to work properly. Maybe on the next one. Happy with the way the peening went, and the G10 is very forgiving if you mis-hit.
-
That is a sweet looking Fieldmaster. Bravo!!!
That's us mobile.
-
Nice work! The rivets look better than my hand done rivets.

-
Excellent work, and I like the density of tools.
-
Thanks chaps.

Syph - I riveted, then polished the heads, then lightly peened again to give a nice beaten finish. Looks good and the G10 is quite resilient and doesn't show marks. Nice material for scales - cheap, easy to work and doesn't need finishing. Stinks though.
It started as a Swiss Champ, which is why there's a tool on the back of the saw. It should be a fine screwdriver, but my friend is into wood carving so I thought a chisel would be more appropriate for her.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
