What did you use your Leatherman for today?
-
Teamed my OHT up with my Vic Explorer to open a reluctant can on air gun pellets.
Sounds like overkill( looked like it too!) but it ended up being a challenge

-
Used the Wave to take out the tiny glass ball out of an empty whiskey bottle....... :D
-
I used one leatherman to take apart another leatherman!
-
I used my Supertool's medium flathead driver to remove a couple light switch covers.
-
Just got a Crunch and today I used it to repair my lawn sprnkler system. It was perfect for getting into the hole and gripping the irrigation pipe. I used the serrated knife blade to cut the risers. All in all, I was very happy with it's performance. I will use it as a supplement to my ST300 and I also carry a Kershaw Select Fire so with these 3 tools I can cover a lot of applications.
Bob -
used the Rebar's philips head to install a new data projector lamp.
-
@BobG said:
Just got a Crunch and today I used it to repair my lawn sprnkler system. It was perfect for getting into the hole and gripping the irrigation pipe. I used the serrated knife blade to cut the risers. All in all, I was very happy with it's performance. I will use it as a supplement to my ST300 and I also carry a Kershaw Select Fire so with these 3 tools I can cover a lot of applications.
BobSo, just a good flashlight and a good bitset and you're covered.

-
-
@bdAmmo said:
Used my Wave to help tie up a few leaders this afternoon.Not sure how a MT helps tie leaders.
For me it would just get in the way and take up use of a hand, but if it works for you then all the better. 
EDIT: Actually pulling the hook (to tighten the knot) with the pliers might be much safer and work out well.
-
You got it Capt. I use the pliers to hold the hook while I tighten the knot. And the scissors to cut the line to length and trim the tag ends.
-
Used my Fuse to open a paint can with a stuck lid. All prying under the rim did was unroll it.
-
I used my TTi today to change a 3 amp lighting plug. But while I was on vacation, my Leatherman was very popular for cutting bread for cheese. We had regular knives, but that's not the point! :D

-
Driving my wife nuts.

I compared the flik of my OHT with the new arrived Gerber MP 600 for hours. :D
-
Used my kitchen draw dwelling Original Supertool, to remove a clump of hair that was blocking my dishwasher water pump.

-
@Lichtbote said:
Driving my wife nuts.
I compared the flik of my OHT with the new arrived Gerber MP 600 for hours. :D
Which tool was the winner?
Sent from the land of the long white cloud.
-
Driving my wife nuts.

I compared the flik of my OHT with the new arrived Gerber MP 600 for hours. :D
Which tool was the winner?
Ouch, whatever answer i will give, it will be a walk through a minefield, right?

Both tools were new/nearly unused, so both needed some breakin on all their joints/pivots. Cleaned them first, then after the some hours i gave them another cleaning to get rid of the black stuff they were oozing out, then re-oiling and so on and so on.
For the pure flik - the leatherman OHT wins with waving banners. It fliks out that smooth .... the 600 moves rougher and so it sounds, also.
Same goes for putting the pliers back in - OHT is way smoother than the MP (wich often needs to be pushed in by hand instead of slipping in by gravity), but the OHT has the habit to stuck on the 2 release pins, then it needs some wiggeling before it slides back in.
-
Driving my wife nuts.

I compared the flik of my OHT with the new arrived Gerber MP 600 for hours. :D
Which tool was the winner?
Ouch, whatever answer i will give, it will be a walk through a minefield, right?

Both tools were new/nearly unused, so both needed some breakin on all their joints/pivots. Cleaned them first, then after the some hours i gave them another cleaning to get rid of the black stuff they were oozing out, then re-oiling and so on and so on.
For the pure flik - the leatherman OHT wins with waving banners. It fliks out that smooth .... the 600 moves rougher and so it sounds, also.
Same goes for putting the pliers back in - OHT is way smoother than the MP (wich often needs to be pushed in by hand instead of slipping in by gravity), but the OHT has the habit to stuck on the 2 release pins, then it needs some wiggeling before it slides back in.
Sorry, that wasn't meant to be loaded. I haven't had either tool and was just wanting an opinion. Thanks.
-
My Sidekick-X's scissors got used to cut a bunch of mudding tape in our future living room.
-
My wave had plenty of use today. I used it to fix the hinge on my iPad case, bend metal brackets in place at work, and cut rope and zip ties while mounting a baby gate.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
