Wave or Rebar?
-
Rebar plus bit extender kit offers capability relevant to your work that Wave can't. The Rebar replaceable bypass cutter performance on stranded copper conductor is awesome compared with non-replaceable bypass cutters. That's a delicate test not a "tough" material test. So Rebar +2.
-
Wave - cause i hate to let go the workpiece im handling, just cause i need both hands to fiddle out some inner tools.
But i have to agree, the rebars head/pliers is nicer - so best would be to buy both, swap the heads, keep the Wave with Rebar pliers - and then resell the Rebar with the Waves old pliers. Or keep it as a backup somewhere.
Or make it right at the first try - get a Surge. :D
Or a OHT.

Or both.

-
You could get both...
We offer a "Tsunami Edition" WAVE with Upgraded Pliers and Functions.
http://www.ebay.com/itm/201071367532?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649TxTC
-
Man! Split down the middle, two and two!
That was the problem...I didn't use the large flat head driver. I used the smaller one because it looked as if the larger one wouldn't fit. After I snapped the smaller flat head, I tried the larger and what do you know, it fit like a charm

What bit extension kit works for the rebar? I didn't know it had one...?
-
@TxToolCrafters said:
You could get both...While i see you writing here ..... any chance you might have a spare saw of a BO Wave in house? I´m asking cause i´ve seen you offering BO serrated blades, and i´m thinking about giving my OHT some longer tools (serrated blade and saw).
-
@jnick said:
What bit extension kit works for the rebar? I didn't know it had one...?Maybe I didn't use the correct term
. I meant this...http://www.leatherman.com/931012.html#start=10
Note that the kit supplied bits are Leatherman 2D but the adapter accepts hex bits.
-
@jnick said:
That was the problem...I didn't use the large flat head driver. I used the smaller one because it looked as if the larger one wouldn't fit. After I snapped the smaller flat head, I tried the larger and what do you know, it fit like a charm
I know the following is not the usual answer here :D , but ..... that sounds as if you were completly fine after your existing tool has been fixed.

Next time you gonna use the correct screwdriver, and all problems are solved without buying another MT. ;)
-
You could get both...
While i see you writing here ..... any chance you might have a spare saw of a BO Wave in house? I´m asking cause i´ve seen you offering BO serrated blades, and i´m thinking about giving my OHT some longer tools (serrated blade and saw).
We are actually in the process of sorting through our spare blades and functions, and should have them listed soon. Send me an email and we can see if we can get it, or any other parts you may need, before that.
-
That was the problem...I didn't use the large flat head driver. I used the smaller one because it looked as if the larger one wouldn't fit. After I snapped the smaller flat head, I tried the larger and what do you know, it fit like a charm

I know the following is not the usual answer here :D , but ..... that sounds as if you were completly fine after your existing tool has been fixed.

Next time you gonna use the correct screwdriver, and all problems are solved without buying another MT. ;)
While you are absolutely correct that I should have used the larger, I don't really think the smaller one should have snapped. Not to mention, I am looking for more than a replacement. I want one with locking tools as to often does my sidekick close while using a driver.
-
Wave plus bit extender and you can use standard 1/4 bits and add reach to boot. I use the 2D bits and have never had any issues with them. I dont cut much so the replaceable cutters aren't a deal breaker but if you do then that will need to be considered. The weight in pocket vs on paper is IMO negligible however when you add the bit kit and extender then perhaps it will need to be considered.
Good luck with your search.
-
Are there any easy mods to get a pocket clip on a rebar? That's the one big thing making me not go with the rebar, at this point.
-
I can't stand carrying around extra bits or bit extenders and the like, and really don't like LM's stubby driver, so my Rebar sees way more carry time than my Charge TTi (which is essentially a Wave for people with more dollars than sense.) Even without scissors, which I normally consider essential.
If you don't mind carrying around the extra parts, a Wave may very well be better as a network admin. But you will need to carry the bit extender, not just a bit clip.
Also, while the bits are still nearly two dimensional, they're a step up over the Phillips on the Sidekick and stick in better.
regarding clips:
Maybe a nite ize clip would work on it? You'd have to check the dimensions, of course.
Dem
-
Having just done a fair bit of work using a Wave, I have to say that the philips, while not full 3d, works great. I had no problems with it slipping out of screws.
I'd vote Wave. It's awesome.
I own both, and the Rebar is a good tool, just not as good as the Wave. I can't count how many times the OHO blades came in handy in the last month.
Also, just so you know, the pocket clip is an accessory for the Wave. It doesn't come with the tool (normally).
So... Wave.
Get the Wave.
Did I mention the Wave?:D
-
Well, I finally did it. Lynn, you were the deciding factor. Considering you said the Phillips has worked well for you, I went with the BO Wave! Just purchased from Amazon with the BO pocket clip. Will be here Tuesday! Can't wait!
Thank you for all of the input.
-
Wave wave wave wave wave wave
D
-
@jnick said:
Are there any easy mods to get a pocket clip on a rebar? That's the one big thing making me not go with the rebar, at this point.Maybe a nite ize clip would work on it? You'd have to check the dimensions, of course.
Dem
Meanwhile in CA...pocket clip upgrade
Nice
those niteize clips look like they are made for the st300/rebar

-
@jnick said:
Well, I finally did it. Lynn, you were the deciding factor. Considering you said the Phillips has worked well for you, I went with the BO Wave!I don't think you'll be disappointed. I think the Wave might be Leatherman's best tool, for the money. The Charge might be better, but I don't think I could ever justify the extra cost for the slight extra comfort.
Please let us know how you're getting along with it once you've had it for a while. We like user stories here.
-
Oooh, thanks Kampfer :). I think I know what I'll be ordering next. That looks like a match made in heaven.
The Charge might be better
Since the Wave has already been chosen, I'm gonna go ahead and derail things a little ;).
I honestly don't think the Charge is better than the Wave. I like mine well enough to hold onto it, but I think it's an overpriced MT. It seems to me that the only thing the Charge totally has over the Wave is the hook on the serrated blade, which I find really handy. Aside from the dual bit driver model of course which could be handy for some. But otherwise...
I think the cap crimper is a silly gimmick and weakens the pliers (and pliers in MTs are weak enough.) I think the only reason the cap crimper is on the Charge is because it makes the plier head different from the Wave. I think premium blade steel is better served on a dedicated blade. And I don't think the thickness added by the scales is a worthwhile tradeoff for the boost in comfort (though I will admit it does feel a lot nicer in hand because of them.)
I like that it comes with a clip and some bits but you could easily get add those to the Wave and still come in for much less cost than the Charge. Really, I think the best thing about the Charge is the gut hook.
I will of course make my regular disclaimer that my opinion on the Wave/Charge design varies considerably from most folks here.
Dem
-
@jnick said:
Well, I finally did it. Lynn, you were the deciding factor. Considering you said the Phillips has worked well for you, I went with the BO Wave! Just purchased from Amazon with the BO pocket clip. Will be here Tuesday! Can't wait!Thank you for all of the input.
Next you should order a Victorinox SwissTool. It's an MT dream come true!!

In all honesty, it's almost impossible to beat the fit and finish of a SwissTool. The tool load out is also fantastic on them. The Supertool is also a fantastic tool, and I love the drivers on my ST200.
I think you'll be quite happy with the Wave though.

-
Dem's comment pretty much sums it up for with wrt the Charge.
I've never had a problem with the edge retention of the Wave, but I have had a problem with chipping the steel. I don't expect the edge to last forever but appreciate not having chunks out of the edge. I can't see a Charge improving anything for me.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
