Wave or Rebar?
-
I love it. Everything is inside fit perfect. Soon I'm add diamond file in it.




-
I love the wave and rebar. I don't think there was a wrong answer here.
Sent from my Nexus 7 using Tapatalk
-
Carry the Wave if ...
- You like/prefer/need outboard saw or file for better access to what you're cutting
- You want OHO blades
- You use non standard driver bits
- You want scissors
- You use the main pliers gripping area a lot
- You want a variety of carry options
- You need a diamond file
Cary the Rebar if ...
- You use standard drivers frequently
- You need to access recessed screws
- You need an awl
- You are likely to be cutting a lot of hard wire
- You need a more aggressive file for softer materials
The "best" tool is the one that best suits your needs (and budget)
-
Have both, EDC both, love both, combine them into a Mini-Surge.
-
@50ft-trad said:
Cary the Rebar if ...- You are likely to be cutting a lot of hard wire
In my practical experience and it's my job, though generally I am compelled to use insulated tools, the engineered edge of the replaceable cutters is vastly superior when trimming (soft) stranded copper conductor.
-
combine become tidal Wave 

-
Got the Wave last night (black oxide) ! I do have a few questions...
-
I noticed that the plier head, the bottom of the cutters are rubbing together when I close the head. Therefore, it has a very "sticky" feel when it closes. Now I'm not sure if this is by design so it stays tight, or if I have a defective Wave. For example, If I close the pier head to where the two ends touch, I can pick up the Wave by the handle, hold it horizontally and the head stays closed, meaning gravity doesn't open the head. Is this normal?
-
All of the handle tools are rather stiff. They almost feel gritty. I already rubbed the entire tool down with some 3-in-1 oil, however the tools are still very stiff. The scissors, actually, won't really come out unless I pry them with another tool. Any suggestion on how I can fix this?
Other than that, the tool seems very nice. My handle edges are nice and rounded, and definitely feel better than the sidekick.
Thanks!
-
-
I assume you bought a new one, not a used - so it´s the way it is and should be, it´s new. :D
It will be easier with time, more using will fasten the process, minor using will take forever.
Additional it helps to "break in" the pivots - wenn you sit in front of your TV -> move every joint as much as you can "klack klack klack ......" the more the better. In between some WD-40 washing, then again moving . Repeat untill it goes easy enough for your taste. -
Congrats on the new Leatherman, I'm sure your Wave will serve you well
.As far as the tightness, it's just as Lichtbote mentioned, it just needs to be used. The BO models seem to take a little longer to break in than their SS counterparts. I gave my Wave a bath in WD-40, worked all the tools, soaked it with more WD-40 and eventually wiped it clean.
-
Leathermans bypass wirecutters are cast so sometimes there is some flash or deformity from cooling that causes them to stick like that. Take a diamond stone and dress them and you will be shipshape.
Sent from my SM-G900V using Tapatalk
-
Yes, Mercury got in first.
A good test is to trim stranded copper flexible conductor. If it cuts cleanly you have good 'un. If any wires get trapped you haven't.
-
@jnick said:
The scissors, actually, won't really come out unless I pry them with another tool. Any suggestion on how I can fix this?This was also the case with my Wave, no amount of WD40 nor opening/closing the tools would help loosening them. I had to loosen up bottom torx screws a little on both handles and all is now buttery smooth, yet solid feel.
Hope this helps.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

