What do we have on the way?
-
@PTRSAK said:
Four 74mm Executives on the way to be fitted with "fancy" scales.These ones will probably get "moved on" when I'm done. I wasn't really wanting to win them, but put a bid on that would make them quite cheap on a per piece basis.
Actually won with my max bid which it went up to several hours before the listing finished.So, if anyone fancies an Executive based "Gentleman's folder" keep your eyes open in a couple of months.
Sweet! I wish you were close to my side of the world then I would have definitley taken one from you and our postal service is really horrid which bums me out even further. This would have been great to add to my collection.I finally have a Ranger and Explorer on the way which I should have by end of this week.
-
I have a couple of TS10 pentalobe screwdrivers on their way so I can hopefully tighten up my OG Wave. I'm thinking I should have bought sockets/ bits instead incase the screws are too tight for the screwdrivers... ??? Anyone had any experience with this?
-
@DazMechanical said:
I have a couple of TS10 pentalobe screwdrivers on their way so I can hopefully tighten up my OG Wave. I'm thinking I should have bought sockets/ bits instead incase the screws are too tight for the screwdrivers... ??? Anyone had any experience with this?Not directly, but I wouldn't think it makes much difference. As long as the tip of the driver is strong enough it should work. Maybe a bit of heat to break the Loctite would help.
Lots of nice stuff on the way to me: A cheap Wingman for mod fodder, a small Tinker, some security driver bits, and some red Alox.
-
@DazMechanical said:
I have a couple of TS10 pentalobe screwdrivers on their way so I can hopefully tighten up my OG Wave. I'm thinking I should have bought sockets/ bits instead incase the screws are too tight for the screwdrivers... ??? Anyone had any experience with this?Just make sure you 'dissolve' that old Loctite on the pivot screws, beforehand.
One way is to use butane torch for 5-6 secs or holding the top and bottom of the tool over your gas stove for about 30 secs or more.Been there done that, it works. :)
-
Awesome!

-
@detron said:
USPS is reporting the Charge SLV going the wrong way, it is currently nearly 1000 Miles away (expected delivery today)have been in contact with seller, he is looking into it, but did verify that he had the correct address. time will tell.
It usually depends on their main sorting hubs. I've had things do the same with Canada Post, so I wouldn't worry..... Yet. :D
-
It is in hand, thanks
sent from phone
-
Thanks to the kindness (and desire to enable ;)) of a member here, I have a LM OHT on the way to try out for a little while. After getting into Gerbers lately, I'm curious to feel out LM's take on the flicky pliers, plus I can test out how well it will carry for me given it will be the bulkiest/heaviest MT I've handled. Can't wait to check it out :D
-
A new (to me) variant on the el-cheapo LM Crunch knock-offs. This one comes in a box labelled as "FOSCO", with a description of "FOSCO 2000 Wise Grip". If anyone wants to look at some photos, here's a link (the seller obviously had more than just the one I bought):
I'm not expecting genuine LM quality, so am unlikely to be too disappointed when it arrives ;)
-
@Monrogue said:
Thanks to the kindness (and desire to enable ;)) of a member here, I have a LM OHT on the way to try out for a little while. After getting into Gerbers lately, I'm curious to feel out LM's take on the flicky pliers, plus I can test out how well it will carry for me given it will be the bulkiest/heaviest MT I've handled. Can't wait to check it out :DHow very nice of them.
I look forward to hearing your opinion. :) -
Very nice indeed
I'm sure I'll like it ;) My primary concern with it is how well it will carry. I don't use sheaths, so I'm hoping it's not too bulky to fit next to my wallet in my back pocket. The weight shouldn't be too bad I don't think, but we'll see. -
A Cybertool 41, won one on the bay for $35 [emoji1]
sent from phone
-
Wingman. Destined for destruction and (hopefully) incorporating the parts into other tools
-
The package from Chi is making it's way to me. Just got into Croatia today. Hopefully it won't take long at the customs office.
-
SwissChamp from Chi's 1k giveaway thread. :D
/topic/54126
-
Pretty nice...and what a great gesture by Chi

-
KF4

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

