Vic combo tool?
-
I think the Waiter has the combi-tool. Maybe the Bartender too. SAKwiki has the Waiter as 84mm and the Waiter Plus as 91mm.
The Vic combination tool has been of two types: the pointed end and the sort of rounded end.
The pointy one is a better improvised phillips driver. Both will cut cans.
Then there's the weird Wenger combi-tool. Any chance this will go into a Vic mod? -
I know about the Waiter plus, but they seem rare. I've searched a few times but can't find anyone selling them either new or used.
I don't actually care about the can/bottle feature, I just need a flathead screwdriver and general prybar thing.
And yes, it'll be a custom 91mm Vic.
-
@Quartz said:
I know about the Waiter plus, but they seem rare. I've searched a few times but can't find anyone selling them either new or used.I don't actually care about the can/bottle feature, I just need a flathead screwdriver and general prybar thing.
And yes, it'll be a custom 91mm Vic.
Be aware the combo tool is notably thinner metal than the standard caplifter/driver

-
I would definitely not recommend the combo for even light prying. It bends VERY easily. Id have no problem using the normal bottle opener to say pry open a can of paint. The combo tool though I bet would bend. Its much thinner and really I'd only recommend them for actual can and bottle opening. Its much less robust as a general tool. Even as a screwdriver the tip will twist if a screw is stuck at all.
-
^^ Absolutely. Using the bottle opener as a pry bar and paint can opener is something I do multiple times a day at the store. The combo tool will not handle such use, as my first Bantam found out the hard way. I will only carry SAKs with a dedicated opener layer at work, and it's also a big reason why I prefer the Explorer to the Yeoman.
-
Ugh. I knew that the combo was thinner and I wouldn't be able to do as much with it, but I didn't think it was quite that bad. The 84mm combo I have loose in my drawer didn't look quite that flimsy (although it's hard to get a good feel for a loose part when you have no leverage).
Is the combo really not even strong enough open a can of paint?
-
@Quartz said:
Ugh. I knew that the combo was thinner and I wouldn't be able to do as much with it, but I didn't think it was quite that bad. The 84mm combo I have loose in my drawer didn't look quite that flimsy (although it's hard to get a good feel for a loose part when you have no leverage).Is the combo really not even strong enough open a can of paint?
It would bend for sure.
To give you an idea how easily bent they are. When I build single layer knife and combo tool mods. I usually need to tweak the bend in the blade and combo a degree or two to have them fit. To bend the blade I clamp the pivot end and hit with a mallot. To bend the combo, I clamp the pivot end and push with my thumb a bit and it bends super easy. Its not a prying tool.
-
It will do the job, but you can feel it's not really up to it. Trust me, I run a paint store. ;) If the lid's on there pretty damn good, like for instance after being on a clamp-type shaker, you'll have a problem.
-
OK, so the loose version of the combo tool I have is the one featured in these two pictures:
I did a cheap strength test buy putting the tang in a vise and then grabbing the end with pliers. Although I can get it to deflect quite a bit (upwards of 20 degrees), after release it always returned back to it's original shape. That is to say, it's rather flexible like a spring. I took it out of the vise and laid it down flat on a table to verify that there's no deformity. It's certainly not something I could permanently bend with just my fingers.
I know this version of the combo tool has a different shape from the 91mm ones, is it also made out of a different type of metal or heat treated differently? In other words, are my findings with this tool invalid vis a vis the version I actually want to use?
-
@jerseydevil said:
^^ Absolutely. Using the bottle opener as a pry bar and paint can opener is something I do multiple times a day at the store. The combo tool will not handle such use, as my first Bantam found out the hard way. I will only carry SAKs with a dedicated opener layer at work, and it's also a big reason why I prefer the Explorer to the Yeoman.Second on that... I've been using the Victorinox 111mm lock flat screw driver/bottle opener on a Dual Pro X for this purpose on some horribly paint-dried older paint tins... they take a beating!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login