EDC Card, Kickstarter Campaign
-
-
@enki_ck said:
I think Mike LOTS might like this one.
He was after a wrench type OPT a few weeks back but most of the Shapeways stuff you had was a bit too pricey.
If you can make this one in large numbers, that would be great and hopefully it will open up a chance for you to do more interesting projects.
Good luck.
I just PM'ed Mike to make sure this project didn't pass him by, in case it does interest him.
I'm sure that even after the Kickstarter campaign has finished, these cards will be available for sale, as we will get quite a few more made than have been pledged for.
As for this project funding others; this will certainly be the case, although I'm not the one at the head of this project, so the funds won't be mine to manipulate. Still, Kickstarter seems to be proving it's usefulness once again, so perhaps I will run my own campaign one day, or help get a full Multitool.org community involved campaign going.
@sparky415 said:
Thats nice Tofty
Thanks Sparky, the next big project could be the MT.O prybar?
@Syph007 said:
Looks neat! I'm a fan of all your design work, it's top notch!
Is the writing laser etched on?
I love your steel choice too, and you are 100% correct Ti alloys are NOT good for tools.Thanks Shph007, likewise. I was fortunate enough to see an example of your work at the last UK meet.
The writing isn't just lasered on, as far as I'm aware it's more of a laser jet process, where a black powder is burned/melted/bonded? into place and to some extent into the metal itself. I'm told it's incredibly hard wearing. In fact it looks like the same finish as the text on the Leatherman Skeletools and Freestyles.
Unfortunately people will always want titanium tools, even me and I know how deficient they are. I call it Atwooditis. Someone asked for a titanium version just last night in the comments section, even though the reason for not using titanium is clearly explained in the listing itself.
Apparently the cards get the full cryo-quenching treatment, so their hardness and resistance to wear should be quite impressive.@JAfromMn said:
My infatuation with fish shaped tools demands I fund this project.
I really hope it gets funded. It looks like a very usable tool for me.Thanks JAfromMn, In that case don't forget this oddity:
It's certainly looking good for the funding goal to be reached; over 40% in 24 hours, isn't a bad start.
@GEARHEAD_ENG said:
Just backed it... very nice design. Are the hex sizes SAE?Thanks for your support GEARHEAD_ENG and welcome aboard.
The hexes are a combination of SAE and metric. A lot of the standard spanner sizes are quite close to each other, so for example; there's no need to have 8mm and 5/16" hexes, as 5/16" is something like 7.95mm.@Gamble said:
Good luck Tofty, you're off to a good start! Don't forget to eat and sleep during the next 29 days
Thanks Gamble, good advice from a crowd funding veteran.
Fortunately I'm not the one in charge of the campaign, so to some extent I can just relax and enjoy the numbers going up.@sardauker said:
Backed.
Thank you
And thank you sardauker. This campaign is going better than I could have expected.
-
-
-
I also wouldn't carry it in my wallet HOWEVER I would carry it in my LM sheath ( if it would fit ). It looks as you could also carry it on a keychain ( circular hole ). The material is an outstanding choice and I'm a big fan of Tofty's designs.
-
-
Wow that got funded pretty fast... less than two days?
-
Glad to hear it.

-
Congrats!

-
-
-

-
Thanks a lot guys, I'm pretty stunned by how quickly the campaign has been successfully funded.
Here's a picture of the two finishes available: (please note that the card on the far right is a prototype and only the ceramic coated cards will have the text on the reverse side as well)
As the funding for the Cards is ever increasing, we've released a $25000 stretch goal, for a thinner card of just 1.6mm, in CPM 3V steel, an even tougher steel. However, 3V is not a stainless steel, so the cards will have a Zirconium Nitride PVD Coating, which will give it a golden, sandy colour. I'm not sure on the projected price yet though.
-
-
-
-
-
-
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


