The Hacked Leatherman Owners Club.
-
Do I change the Surge to match the Charge, the Charge to match the Surge or leave the layout different?

I wouldn't match any to any, just leave it be. You've done the pliers and owl change, you don't really need Wingman's scissors on a Charge or whatever...
Well the scissors are in and both have identical tool loads. Should I match the locations as well...

-

;)
-
Lol!
Nate
-
Lol. It's actually closer to the SurCharge I modded since it's in the Charge body with Ti scales.
</post/952392>
-
@Toolslinger said:
Lol. It's actually closer to the SurCharge I modded since it's in the Charge body with Ti scales.</post/952392>
The SurCharge it is, then ;)
-
Lol. It's actually closer to the SurCharge I modded since it's in the Charge body with Ti scales.
</post/952392>
The SurCharge it is, then ;)
I'm honoured
. -
Today my BO Wave serrated blade from Texas Toolcrafter came - and after a few minutes of fiddling how it will fit the OHT, it hacked me. :D
Where is a Surge(on) when you need one?

Usually i don´t cut myself very often, not that much that it needs more care than sticking the finger in the mouth for a few minutes - but this time it had to got a immediate bath with superglue. The cut goes from the most left "red" end to the right, an in a 45° angle to the inside.
It reminds me why i don´t cut myself more often - it hurts and the spilled blood needs to be cleaned. :ahhh
After that i wanted to make the needed bushing from some round brass on my lathe (the Waves holes are a little bit bigger), but i found no 4,7mm drill - and no shop in our small town had anything than the most used sizes in 0,5mm steps - 4,0 then 4,5 then 5,0 (thats what i have at home myself).

Not sure if that´s maybe a sign to don´t mod the OHT?


-
@Lichtbote said:
It reminds me why i don´t cut myself more often - it hurts and the spilled blood needs to be cleaned.^definitely this.
-
Lol. It's actually closer to the SurCharge I modded since it's in the Charge body with Ti scales.
</post/952392>
The SurCharge it is, then ;)
It already has a name.
Might give it a new name though to go with the recent hack.
I replaced the inner scissors with the large screwdriver which is very handy. -
Och! >:(
-
@Lichtbote said:
Today my BO Wave serrated blade from Texas Toolcrafter came - and after a few minutes of fiddling how it will fit the OHT, it hacked me. :DWhere is a Surge(on) when you need one?

Usually i don´t cut myself very often, not that much that it needs more care than sticking the finger in the mouth for a few minutes - but this time it had to got a immediate bath with superglue. The cut goes from the most left "red" end to the right, an in a 45° angle to the inside.
It reminds me why i don´t cut myself more often - it hurts and the spilled blood needs to be cleaned. :ahhh
After that i wanted to make the needed bushing from some round brass on my lathe (the Waves holes are a little bit bigger), but i found no 4,7mm drill - and no shop in our small town had anything than the most used sizes in 0,5mm steps - 4,0 then 4,5 then 5,0 (thats what i have at home myself).

Not sure if that´s maybe a sign to don´t mod the OHT?

Sort your stuff out mate.
Improvise. 
-
I tried improvising :D - but the 4,5mm hole was exactly 4,5mm - the runout was to good (what is usually a good thing).
Probably i could even use a 5mm drill and wouldn´t notice it later when using
- but i would always know that, and that´s not the way of german engineering. 
Tried to come around the expend for a set of drills with 0,1mm steps, as a good set is easily around 100€ ::) and usually the 0,5mm steps are OK for most of my work. But i´m afraid i need to buy them.
-
You know you have a MT obsession when you buy tools just to work on your multi-tools.
-
That´s not my major problem.

I buy big machines to restore bigger machines which i don´t need cause i bought the big machines already and they could do the work i need machines for.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



