The Hacked Leatherman Owners Club.
-
@Lichtbote said:
Today my BO Wave serrated blade from Texas Toolcrafter came - and after a few minutes of fiddling how it will fit the OHT, it hacked me. :DWhere is a Surge(on) when you need one?

Usually i don´t cut myself very often, not that much that it needs more care than sticking the finger in the mouth for a few minutes - but this time it had to got a immediate bath with superglue. The cut goes from the most left "red" end to the right, an in a 45° angle to the inside.
It reminds me why i don´t cut myself more often - it hurts and the spilled blood needs to be cleaned. :ahhh
After that i wanted to make the needed bushing from some round brass on my lathe (the Waves holes are a little bit bigger), but i found no 4,7mm drill - and no shop in our small town had anything than the most used sizes in 0,5mm steps - 4,0 then 4,5 then 5,0 (thats what i have at home myself).

Not sure if that´s maybe a sign to don´t mod the OHT?

Sort your stuff out mate.
Improvise. 
-
I tried improvising :D - but the 4,5mm hole was exactly 4,5mm - the runout was to good (what is usually a good thing).
Probably i could even use a 5mm drill and wouldn´t notice it later when using
- but i would always know that, and that´s not the way of german engineering. 
Tried to come around the expend for a set of drills with 0,1mm steps, as a good set is easily around 100€ ::) and usually the 0,5mm steps are OK for most of my work. But i´m afraid i need to buy them.
-
You know you have a MT obsession when you buy tools just to work on your multi-tools.
-
That´s not my major problem.

I buy big machines to restore bigger machines which i don´t need cause i bought the big machines already and they could do the work i need machines for.

-
Uh oh that looks painful... :-\
@Lichtbote said:
Not sure if that´s maybe a sign to don´t mod the OHT?
Out of interest what are you wanting to replace/upgrade on the OHT? Just a note that if you're looking at adding a non-OHT tool to your OHT, the OHT outward tools come with a slightly non-standard LM tool design (base area around the pivot is different) and they're in general slightly thinner to fit under thin profiled scales. So you'd need quite a bit of re-shaping done, IMO. But I could be wrong as I don't know what your end goal is.
Cheers.
-
Nothing special, just replacing the short OHTs serrated blade and saw with the larger ones from a Wave. Making some brass bushings to bring the 5,6mm holes of the Waves tools to fit the 4,7mm pin of the OHT, reshaping the base, maybe new shims if the thickness is to much off.
And after they fit, then trying to get their tips shaped in a way that the can-opener and the small screwdriver do not have to go. Or delete them if needed.
-
@Lichtbote said:
Nothing special, just replacing the short OHTs serrated blade and saw with the larger ones from a Wave. Making some brass bushings to bring the 5,6mm holes of the Waves tools to fit the 4,7mm pin of the OHT, reshaping the base, maybe new shims if the thickness is to much off.And after they fit, then trying to get their tips shaped in a way that the can-opener and the small screwdriver do not have to go. Or delete them if needed.
Sounds painful, good luck :)
-
Sort your stuff out mate.
Improvise. 
I tried improvising :D - but the 4,5mm hole was exactly 4,5mm - the runout was to good (what is usually a good thing).
Probably i could even use a 5mm drill and wouldn´t notice it later when using
- but i would always know that, and that´s not the way of german engineering. 
Tried to come around the expend for a set of drills with 0,1mm steps, as a good set is easily around 100€ ::) and usually the 0,5mm steps are OK for most of my work. But i´m afraid i need to buy them.
Drill the 4.5mm and file the rest out by hand. I did the Wingman scissors with a chainsaw file.

-
That's how I know a knife or tool is meant to be mine, within the first 24 hours I get a new slice and scar
-
Drill the 4.5mm and file the rest out by hand. I did the Wingman scissors with a chainsaw file.

I thought to do that - and already had the rat-tail needlefile in my hand ...... ;)
But then i wanted it ...... well, german.

I think we are similar in what we want, I just don't have the resources. :)
-
I'm starting to think one of those 10$ harbor freight rotary tools are looking tempting for some mod help
-
Drill the 4.5mm and file the rest out by hand. I did the Wingman scissors with a chainsaw file.

I thought to do that - and already had the rat-tail needlefile in my hand ...... ;)
But then i wanted it ...... well, german.

Or drill undersize and use a small boring bar on the lathe
-
It took me years to collect that machinery, and the one or another "No" when i wanted other stuff, to collect the money. No drinking and no smoking helped, too. And doing most of the restoration myself.
There are always bargains out there for good old drillpress/mills/lathes/grinders - often not good looking, but the old stuff is usually sturdy. Keep an eye on craigslist, garage sales, .....
A sturdy drillpress is the most versatile, with a vise it could even be used as a lathe, sort of.
-
@GEARHEAD_ENG said:
Or drill undersize and use a small boring bar on the latheMy smallest boring bar has a 8mm shank + the protruding 0702 DCGT carbide bit - could be hard to fit that into a 4,5mm hole. ;)
(I know there is very small tooling like "Horn" steels that could do it, but i have no such tiny tools.)
-
Sort your stuff out mate. :twak: Improvise. :pok:
I tried improvising :D - but the 4,5mm hole was exactly 4,5mm - the runout was to good (what is usually a good thing). :whistle: Probably i could even use a 5mm drill and wouldn´t notice it later when using :think: - but i would always know that, and that´s not the way of german engineering. :rofl:
Tried to come around the expend for a set of drills with 0,1mm steps, as a good set is easily around 100€ ::) and usually the 0,5mm steps are OK for most of my work. But i´m afraid i need to buy them.
4.8mm cobalt drills are readily available. What us Europeans call 3/16" I think.
Give this one a miss though...
-
Nice price. :DThere is one toolshop in town that should carry the unusual sized drills, yesterday it was closed - i will give it a try today.
-
Just a quick picture of a modified juice handle! All it is is the 2 knife blades. Simple every day pocket carry for a knife!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
