The Hacked Leatherman Owners Club.
-
Yes, the new Wave handles still have those small bumps to stop the lock release tabs, but they didn't present any issues. I put the awl in the scissors spot, and the profile of the awl allows clearance of that bump. Ditto for the curvature of the underside of the Phillips driver.

I had to put a notch into the Phillips to clear the bump. The Large Screwdriver and Awl were also held up by it.
interesting. I wonder if this is because you're removing the springs/pins on your mods, which allows the drivers/awl to close further?

I do take some metal off the underside of the Phillips as well when I grind it down to fit, so that could be part of it as well. I've never had a problem with the large flat driver, since that comes stock on a Wave. are you putting it in a different spot?
-
I don't have one in BO, but I'd be happy to help you track down a donor BO Surge on ebay if you'd like.

That would be a great help, thanks. :)
I wonder if it might be a option to look for the stainless, too. Maybe i can give it to http://www.blackoxyde.nl/ to blacken it, it´s not that far from work.
Why don't you make one up to fit the brand of blades you'll be using? That would thin it out to about right.
-
Yes, the new Wave handles still have those small bumps to stop the lock release tabs, but they didn't present any issues. I put the awl in the scissors spot, and the profile of the awl allows clearance of that bump. Ditto for the curvature of the underside of the Phillips driver.

I had to put a notch into the Phillips to clear the bump. The Large Screwdriver and Awl were also held up by it.
interesting. I wonder if this is because you're removing the springs/pins on your mods, which allows the drivers/awl to close further?

I do take some metal off the underside of the Phillips as well when I grind it down to fit, so that could be part of it as well. I've never had a problem with the large flat driver, since that comes stock on a Wave. are you putting it in a different spot?
Yeah the issue is only when in the scissors place.
The handles would close but the nail nick/hook would sit proud.
I wanted this one all flush though.Another interesting one was I had to very slightly reprofile the scissors handle to clear the Rebar pliers.
But when detron did the same hack he said it fitted in without any problems.
Both were done with original TTi handles.Was thinking of starting on the skinny hack but I'm not sure it would get much use. Feeling so unmotivated.
-
Why don't you make one up to fit the brand of blades you'll be using? That would thin it out to about right.
I´m using the standard t-shanks (as far as i know there are no other available here anymore), so i don´t think i could make one smaller than the Surge exchanger
The bosch t-shanks I use are about half the thickness of the leatherman ones.
I use a heatshrink sleeve with both versions of the Surge to get rid of the wiggle.
-
Bosch, Hitachi, ... - i´m using several brands. The nice thing with the Surge exchanger is the spring on its side which balances the different thicknesses a little bit. The whole construction is so nice and thoughtfull, i doubt i could came with something as good and noticeable thinner.
-
@zoidberg said:
Was thinking of starting on the skinny hack but I'm not sure it would get much use. Feeling so unmotivated.I always want them to be all flush. :D
I've always had to reprofile the scissors since I like to leave the springs/pins in place. ;) but there have been some slight changes to the Wave/Charge scissors over the last few years; could just be that you and detron were working with 2 different versions.
I have some hacks that I want to try for myself, I just need to find the time... and the motivation, like you said. :-\ I've got multiple disassembled tools that are just waiting to be hacked and put back together...
-
Got rid of the bit holder on my wave, not missing it so far :D
-
Time will tell... its my wifes, and pretty sure its going to be more of an emergency tool than anything.
-
Then .... why deleted the bit holder?

-
Fiddling around while watching a movie. I have a problem with fixing things before they are broken :D
But the longer reach is nice, -
:D
-
This Micra looks a little different. ???


-
Spare Micra knife blade converted into an awl.
Like it very much.

-
I'm gonna try longer bits but didn't have a spare.
-
Thanks :D
Maybe, but the surge seems to have more room for some reason, maybe because of the angle of the new plier head? I'll try it soon hopefully
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login