And so it begins.... (My adventures into Alox!)
-
I still think you could shift a few on a fishing forum.
-
I still think you could shift a few on a fishing forum.
Call it a "<u>tactical Swiss hook dislodger</u>" :P :P
Will that remove the hook from the back of my Climber?
Negative. The Tactical Swiss hook dislodger, can not take out a Tactical Assault Parcel Hook.
Nate
-
I still think you could shift a few on a fishing forum.
Call it a "<u>tactical Swiss hook dislodger</u>" :P :P
Will that remove the hook from the back of my Climber?
Negative. The Tactical Swiss hook dislodger, can not take out a Tactical Assault Parcel Hook.
Nate
Yeah, those things are TAPH!

-
Today's work was on a big alox monster with brass liners.

I like to use long brass rods for fitups before I use the finished scales or tools. All the Vic parts in this picture are all from my fit up parts and are ones that used solely for fitups. I dont use the same tools I will deliver on a custom so they remain in perfect condition until final assembly.

The springs and liners are the only finished part I am making at this stage. Here is what the back looks like before I work on the springs. Notice the custom spring I make is not finished at this stage. It actually sits proud of the other springs and I grind it flush and then finish all springs at that time.

The result is a nice uniform looking back, with my custom spring blending right into the stock springs. I polish them all the same along with the liners for a high end fit and finish.

Understandably I get alot of people asking to buy springs from me for the scissors layer, but I dont sell them since they arent ready to use as is. I finish them as part of the build, so that is why they are not a ready to go part.
Here is the big blue monster all finished up.






Cheers!
-
That is about as close to a perfect tool layout in a SAK I could ask for.

Could you PM me what that would cost me just for future reference.

-
@Syph007 said:
Today's work was on a big alox monster with brass liners.
I like to use long brass rods for fitups before I use the finished scales or tools. All the Vic parts in this picture are all from my fit up parts and are ones that used solely for fitups. I dont use the same tools I will deliver on a custom so they remain in perfect condition until final assembly.

The springs and liners are the only finished part I am making at this stage. Here is what the back looks like before I work on the springs. Notice the custom spring I make is not finished at this stage. It actually sits proud of the other springs and I grind it flush and then finish all springs at that time.

The result is a nice uniform looking back, with my custom spring blending right into the stock springs. I polish them all the same along with the liners for a high end fit and finish.

Understandably I get alot of people asking to buy springs from me for the scissors layer, but I dont sell them since they arent ready to use as is. I finish them as part of the build, so that is why they are not a ready to go part.
Here is the big blue monster all finished up.






Cheers!

-
Beauty as usual syph! Good job
JR -
Thanks for sharing part of the process, I really liked it.

-
Really enjoy your work
-
Wow! Amazing work as usual sir!

Add a file to it and market it as the SyphChamp!
-
Pioneer + wood saw configuration! Why hasn't Vic thought of this one! :D

-
-
Pioneer + wood saw configuration! Why hasn't Vic thought of this one! :D

:D That sounds like a useful tool loadout. What are you going to call it?
Hmmm tough call. If I was following cellidor naming conventions this would be a pioneer camper. If it was up to me though... I like Pioneer Homesteader! :D Or maybe a homesteader might need scissors too... hmmm :D
-
@captain spaulding said:
That is about as close to a perfect tool layout in a SAK I could ask for.
Could you PM me what that would cost me just for future reference.

Same here, would be most grateful if you could PM me- I think that's the tool layout I want eventually though I haven't decided which scales and liners etc

-
Time to make up more 0.005" phosphor bronze washers.








-
Nice to see the technique.
Doesn't it work out cheaper to buy them though, factoring in your time etc? For example:
http://www.seastrom-mfg.com/washerresults.aspx?pl=round+flat+washers&pc=washers,+flat+round&qs=5720&sp=wb_getallwasherdetailsbylinecatpnp&ct=5720:++Phosphor+Bronze+Round+Flat+Washer -
@neillcurrie said:
Nice to see the technique.
Doesn't it work out cheaper to buy them though, factoring in your time etc? For example:
http://www.seastrom-mfg.com/washerresults.aspx?pl=round+flat+washers&pc=washers,+flat+round&qs=5720&sp=wb_getallwasherdetailsbylinecatpnp&ct=5720:++Phosphor+Bronze+Round+Flat+WasherThey dont have the size I need, but if they were cheap enough maybe. I need ID 0.125, OD 0.300 and thickness 0.005. A whole sheet of this is only a few dollars and time to make is maybe 20 minutes for quite a few (40 something in this case) so a few pennies per washer and 30 seconds of time (20 minutes for 40).
I buy sheets in 0.005, 0.010. 0.015 0.020 in phosphor bronze, nickel silver and brass so that I can make whatever type and size of washer I need when I need it. It works out fine as long as I make lots at once. It would not be a good use of time to only make enough for whatever SAK I was building at the time.
I used to buy them from usaknifemaker, but I still had to turn down the OD anyhow, so now its just as easy to make them from sheet stock.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login