The Hacked Leatherman Owners Club.
-
:D Thanks but due to a lack of funds and parts I won't be trying anything for a while.
-
yup!
I mostly want to try the Surge scissors just to see if I can pull it off. :D@zoidberg said:
I'm not liking the Wingman scissors very well just yet. May have to find some 91mm or Surge scissors and try this. I already put my spare Surge scissors in the ST300.It's been done by one of the members of another forum, if memory serves me right it was over at British Blades.
The mod while functional, left a lot to be desired. The Surge scissors were just too long for Wave/Charge, so the modder had to saw off quite of bit of the tips leaving the unsightly and stumpy looking implement. The problem with Surge scissors isn't so much the length of its blades but the long handles. As a result a scissor pivot is too far down and blade tips need to be almost cut in half to fit the Wave/Charge cavity.
If I was doing this mod I would rather focus on the handle bottom stop and remove the little nub to add few more mm in total cavity length.
that's pretty much what I had in mind... I think I'd also have to shorten the pivot if I remove/grind down the bottom handle piece on the Wave.

zoidberg, I agree with you about the Wingman scissors. they work well enough in my skinny ReCharge because I use them for a very specific purpose (cutting open small plastic packages in the lab at work), but for general purpose use, they're certainly not the best scissors. :(
I picked up a couple used 91mm Vics on ebay awhile back, I think I'll try those scissors next.
-
that's a lot of hacking going on
-
-
-
Very cool!
-
@hiraethus said:
A bit of grinding, sanding and layer swapping later:

Nice lightweight, UK friendly multi tool now. Just need a pocket clip and it'll be done.looking good!
did you have to grind the plier head at all to allow clearance for the Vic scissors, or were the scissors thin enough to allow clearance? -
Thanks! Not the pliers, but I did sand down the plastic liner next to the scissors and ground about 0.5mm of the thickness of the Phillips driver to give the scissors more space. I had to add a thicker washer between the pliers and the liner to take up the gap - I should have left a thicker portion at the pliers end.
-
Just a hint on something nice I've been working on... ;)
Still adding final few touches, not sure when will I be able to complete it, work is currently hectic.

-
:D

That reminds me i have to work on the refurbish of my polishing machine (atm still a big bad 12" grinder).

-
Would love to have a go at polishing my Wave once I get home.
Anyone know of a thread or guide how to go about something like this?
-
@hiraethus said:
Hacked Wave with Wingman scissors, small bit driver removed and awl/small flat driver added:

Not sure how I missed this but did all the parts you added come from the Wingman?
Also is the Scissors mod a simple drop in?
Thanks.
-
@hiraethus said:
Thanks! Not the pliers, but I did sand down the plastic liner next to the scissors and ground about 0.5mm of the thickness of the Phillips driver to give the scissors more space. I had to add a thicker washer between the pliers and the liner to take up the gap - I should have left a thicker portion at the pliers end.I didn't even think of sanding down the liner -- great idea!

-
Hacked Wave with Wingman scissors, small bit driver removed and awl/small flat driver added:

Not sure how I missed this but did all the parts you added come from the Wingman?
Also is the Scissors mod a simple drop in?
Thanks.
Looking at the pic, the scissors definitely came from a Wingman, but it looks like the small flat driver is the Kick/Fuse/Blast variety, and the awl looks like a ground-down large flat driver.
The Wingman scissors are not quite a straight drop-in; the pivot hole needs to be enlarged to fit the Wave pivots.
-
^^ What he said.

I had to tickle a tiny bit off one corner of the saw too, so it locked easily when I moved it to the serrated blade slot. The small flat driver is modified too, to clear the lock pivot.
-
So I just went though this whole dang thread. Came here thinking I would do a little research but pretty much knowing what I wanted to do to my Wave.
Add Rebar head and Awl. Lose the stupid mini driver.
Now I am thinking some kind of outside Vic Scissors, S30V blade, Rebar Awl and Head but have no idea what to put in the mini driver spot if the awl goes into the scissors spot.

-
@Lichtbote said:
:D
That reminds me i have to work on the refurbish of my polishing machine (atm still a big bad 12" grinder).

I wish I had a machine for this, I use old manual elbow grease method :(
It's long and tedious process doing this by hand, but a labor of love. (I'm sure there's a dirty joke somewhere there :P)
-
@babola said:
I wish I had a machine for this, I use old manual elbow grease method :(It's long and tedious process doing this by hand, but a labor of love. (I'm sure there's a dirty joke somewhere there :P)
Check ebay/craigs list/local newspapers for sale pages - look out for an old, bad looking and cheap bench grinder - as big as possible (bigger means more power). If it looks like crap they usually go cheap. All it has to do is still running (maybe have an electrician check the old cables for todays standards) - then you can disassemble it´s pretection covers and the grinding wheels. Then check the size of it´s axle, and go to ebay (or search the net for shops) to look for the right sized polishingwheel adapters.
With some time for a good offer you should have a polishing machine at the end, for under the price of a Surge.

(For the good feeling i usually disassemble my machines, put new bearings in, some new paint. But that is rarely really needed for proper function.)
-
I wish I had a machine for this, I use old manual elbow grease method :(
It's long and tedious process doing this by hand, but a labor of love. (I'm sure there's a dirty joke somewhere there :P)
Check ebay/craigs list/local newspapers for sale pages - look out for an old, bad looking and cheap bench grinder - as big as possible (bigger means more power). If it looks like crap they usually go cheap. All it has to do is still running (maybe have an electrician check the old cables for todays standards) - then you can disassemble it´s pretection covers and the grinding wheels. Then check the size of it´s axle, and go to ebay (or search the net for shops) to look for the right sized polishingwheel adapters.
With some time for a good offer you should have a polishing machine at the end, for under the price of a Surge.

(For the good feeling i usually disassemble my machines, put new bearings in, some new paint. But that is rarely really needed for proper function.)
Thanks mate, I think my manual method will have to do for a while, though. :P
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

