Bit Kit for CyberTool
-
Great find!

Can you list the benefit on tools compared to the original Victorinox bits?
Original bits:
Slotted 3mm, 4mm
Phillips 0, 1, 2
Torx 6, 8, 10, 15
Inbus 1.2mm, 1.5mm, 2mm, 2.5mm, 4mm -
This one.

-
Can you list the benefit on tools compared to the original Victorinox bits?
Original bits:
Slotted 3mm, 4mm
Phillips 0, 1, 2
Torx 6, 8, 10, 15
Inbus 1.2mm, 1.5mm, 2mm, 2.5mm, 4mmPZ0 / PZ00
Torx 7&9
Adapter to 1/4" square (see picture 2 bottom center)Also a screwdriver is superior/faster if you have tons of screws.
-
@kkokkolis said:
This one.Do this bits work with the CT (without adding a magnet)?
-
Great find!

Can you list the benefit on tools compared to the original Victorinox bits?
Original bits:
Slotted 3mm, 4mm
Phillips 0, 1, 2
Torx 6, 8, 10, 15
Inbus 1.2mm, 1.5mm, 2mm, 2.5mm, 4mmPZ0 / PZ00
Torx 7&9
Adapter to 1/4" square (see picture 2 bottom center)Also a screwdriver is superior/faster if you have tons of screws.
Also, often you need more than one bit at the same time, so its great to have a second bit-holder.
-
I use the 4mm bits from a generic screwdriver set from Home Depot, cost about $5 for 50+ bits of all types. A small magnet JB-welded into the cybertool holds the ball-less bits perfectly.I made a couple of extensions from the parts left over, one is a 4mm extension, the other is an extension that goes from 4mm to 1/4". Covers all bases. There's a thread or two on the best parts etc.
-
@neillcurrie said:
I use the 4mm bits from a generic screwdriver set from Home Depot, cost about $5 for 50+ bits of all types. A small magnet JB-welded into the cybertool holds the ball-less bits perfectly.I made a couple of extensions from the parts left over, one is a 4mm extension, the other is an extension that goes from 4mm to 1/4". Covers all bases. There's a thread or two on the best parts etc.Agreed, for a lot of applications a magnet is the solution. However, I get a bit paranoid if I have to replace the CPU fan on Server that has to go back on-line ASAP. I don't like to take chances on these occasions despite the fact I have never had problems with magnetic bit-holders.
-
This one.
Do this bits work with the CT (without adding a magnet)?
No, they are regular 4mm, but I added a magnet anyway. Yours have springed balls, I missed that detail.
-
This one.
Do this bits work with the CT (without adding a magnet)?
No, they are regular 4mm, but I added a magnet anyway. Yours have springed balls, I missed that detail.
Yes and for most I think that is a good solution... There are just a few occasions where I don't want to risk it.
-
Great find, Beat.

How much does the bit kit go for?
-
-
-
Can your say that again? :D
-
-
Can your say that again? :D
:D
You easily pay $10 for a beer in Zurich ($20 for an exotic might be exaggerated)
Yeah, quite crazy prices really. You should came here for a few
Even if you travel by plane it might be cheaper than going out for a night on a town in Zürich. >:D Domestic is a bit over $2 and most of the other stuff you can get for under $3. (in bars that is) Any special brews might cost a bit more but nowhere near Swiss prices. -
Can your say that again? :D
:D
You easily pay $10 for a beer in Zurich ($20 for an exotic might be exaggerated)
Yeah, quite crazy prices really. You should came here for a few
Even if you travel by plane it might be cheaper than going out for a night on a town in Zürich. >:D Domestic is a bit over $2 and most of the other stuff you can get for under $3. (in bars that is) Any special brews might cost a bit more but nowhere near Swiss prices.Its the reason why I drink at home, more comfy and way cheaper...
-
Finding 6mm hex bits in the states with the little ball retention is impossible.
-
I use the 4mm bits from a generic screwdriver set from Home Depot, cost about $5 for 50+ bits of all types. A small magnet JB-welded into the cybertool holds the ball-less bits perfectly.I made a couple of extensions from the parts left over, one is a 4mm extension, the other is an extension that goes from 4mm to 1/4". Covers all bases. There's a thread or two on the best parts etc.
Agreed, for a lot of applications a magnet is the solution. However, I get a bit paranoid if I have to replace the CPU fan on Server that has to go back on-line ASAP. I don't like to take chances on these occasions despite the fact I have never had problems with magnetic bit-holders.
I wouldn't worry about losing any bits that are held in just by a small magnet.
I did the magnet-add to my cybertool, and I can pick up the whole CT34 using just the bit in the holder and swing it around. Those magnets are incredibly strong, yet you can get the bits out of the holder OK. Maybe not so if your hands are slippery with oil or grease :) -
I use the 4mm bits from a generic screwdriver set from Home Depot, cost about $5 for 50+ bits of all types. A small magnet JB-welded into the cybertool holds the ball-less bits perfectly.I made a couple of extensions from the parts left over, one is a 4mm extension, the other is an extension that goes from 4mm to 1/4". Covers all bases. There's a thread or two on the best parts etc.
Agreed, for a lot of applications a magnet is the solution. However, I get a bit paranoid if I have to replace the CPU fan on Server that has to go back on-line ASAP. I don't like to take chances on these occasions despite the fact I have never had problems with magnetic bit-holders.
I wouldn't worry about losing any bits that are held in just by a small magnet.
I did the magnet-add to my cybertool, and I can pick up the whole CT34 using just the bit in the holder and swing it around. Those magnets are incredibly strong, yet you can get the bits out of the holder OK. Maybe not so if your hands are slippery with oil or grease :)I'm not worried about loosing bits, its sheer paranoia concerning the mixing of magnets and electronics ;)
[...]I get a bit paranoid if I have to replace the CPU fan on Server that has to go back on-line ASAP. I don't like to take chances on these occasions despite the fact I have never had problems with magnetic bit-holders.
-
@Etherealicer said:
I'm not worried about loosing bits, its sheer paranoia concerning the mixing of magnets and electronics ;)Not a problem. I've used magnetic screwdrivers for over a decade servicing office electronics and computers without issue. NOT having a magnetic screwdriver is a bigger issue. Dropping one screw can make a 1/2 hr job last all day...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login