'Les Stroud' Engage Multitool TEST TO DESTRUCTION!
-
Survivorman - Les Stroud
Survivorman - Les Stroud. 287.765 Follower · 17.217 Personen sprechen darüber. Welcome to the official (and real) Les Stroud page!
(www.facebook.com)
-
Cant find any comments about the tool there, but I suck at facebook.
Sent from a device made from star dust using tapatalk
-
Stuff like this really is sad, especially for us. People sell out like it's not even a concern, I would refuse to put my name on anything that didn't far exceed any expectations I had because the last thigh I want is my name sullied.
On the other side, it's a real let down for us because there was so much potential. It could have been the revival of a historic brand and another serious entry into our favorite market. But instead of something for us all to get excited over, we get trash.
-
Sure, but you have to admit, it IS providing us all some entertainment. :D
-
WARNING: This post is straight-up abuse. However, we do learn some things.
Engage faces his worst nemesis, the Paver: a 15 lb concrete paving stone, and his trusty sidekick Sidekick is nowhere to be seen!
Will he survive?
Test one, a sharp blow from the paving stone, dropped at about three inch height onto the tool while it lays flat.

The rubber/plastic grips did a fine job of absorbing the hit. plastic handle popped out but no huge damage.
Next, three hits on the tool, again from about three inches. The tool is on its side. First hit at the tool pivot end, second mid-tool, and third at the plier end.
Damage? Broken plastic hand insert is now broken off.

The Paver takes a break for a minute. Here I use a hammer to drive the plier jaws shut, cutting a heavy nail in half.

Results? Holy... smurf! Seven hard blows on the plier heads with a hammer, and the nail cuts. Nothing but scratches on plier head. Tip of the nail went flying off, and is nowhere to be found.

Back to the paver. I repeated the three-drop test, this time at 6 inches. The tool end takes a serious hit...

The 'backspring' broke off. This not only prevents ANY kind of tool retention in the open position, it also allows the tools to swing freely THROUGH the handle...

As that blade now presents REAL safety issues, it was necessary to do this next, obviously abusive test on the blade. Can it cut through a paving stone?

Of course not. It was really about grinding the edge off that blade.
I forgot to take a pic of it, but I also propped up the plier end and dropped the paver edge onto the plier jaws just forward of the pivot. SEVEN TIMES, at 6 inches. No damage besides scratches.
I dropped the paver on the tool while it was closed with plier head up, four times from 6 inches.
Holy... crap. All the intentional abuse done to the pliers, twisting, hammering, driving the jaws closed on a nail with a hammer... The plier head on this tool has proven incredibly strong.

Credit where credit is due: SUPER PLIER HEAD WIN!
-
Great post Lynn.

-
Need to increase the height of the drop on that paver methinks.
Great test though. Not sure what else we can do to it short of strapping it to some explosives...

-
I still haven't run down to the hardware store for a blowtorch, but yeah, we're getting to 'extreme abuse' stage.
:D
Ahem... not that makes me happy or anything.

-
@Lynn LeFey said:
I still haven't run down to the hardware store for a blowtorch, but yeah, we're getting to 'extreme abuse' stage.Well, what are you waiting for?

-
Ugh! I mean, it's like WAY down the hill, and I'd have to MOVE or something... and there's leftover PIE calling my name, and the stars aren't aligned properly, and I think I'm getting a cold, and I have a crushing fear of crowds, and the barometric pressure is pretty high, or low, or something, it might rain.
But mostly because I'm lazy, and justifying buying a blowtorch to crisp up a MT when we're about to get a $1600 vet bill is one of those things that would make hubby 'unhappy'.
-
@Lynn LeFey said:
Ugh! I mean, it's like WAY down the hill, and I'd have to MOVE or something... and there's leftover PIE calling my name, and the stars aren't aligned properly, and I think I'm getting a cold, and I have a crushing fear of crowds, and the barometric pressure is pretty high, or low, or something, it might rain.But mostly because I'm lazy, and justifying buying a blowtorch to crisp up a MT when we're about to get a $1600 vet bill is one of those things that would make hubby 'unhappy'.
Excuses, excuses. :P Actually, leftover pie is a pretty good excuse.......
-
Leftover pie is a great excuse. Now I just need to make pie so I can have leftovers...
-
Did someone say pie :ahhh hold on I think there's still some pecan.
-
I was looking at the tool a few minutes ago, and noticed what an ebay seller might call a 'very slight defect'.


The handle is bent all wonky.
-
Almost new.
-
@Lynn LeFey said:
I was looking at the tool a few minutes ago, and noticed what an ebay seller might call a 'very slight defect'.


The handle is bent all wonky.
I think its time to take it out behind the chemical shed and arrange a detail of 6 men to shoot it.
-
@Higgins617 said:
Stuff like this really is sad, especially for us. People sell out like it's not even a concern, I would refuse to put my name on anything that didn't far exceed any expectations I had because the last thigh I want is my name sullied.On the other side, it's a real let down for us because there was so much potential. It could have been the revival of a historic brand and another serious entry into our favorite market. But instead of something for us all to get excited over, we get trash.
Totally agree, I mean given all the knowledge these survival celebrities posses, you will assume they would know what tool is right for the job, let alone given the chance to potentially building it ground-up. And instead of making a robust fool-proof tool good for harsh wilderness use, it is certainly no where near the average(or even the inexpensive) competitions. To put personal name on that tool will be like admitting poor preparation is acceptable...

-
@Lynn LeFey said:
I was looking at the tool a few minutes ago, and noticed what an ebay seller might call a 'very slight defect'.


The handle is bent all wonky.
I think its time to take it out behind the chemical shed and arrange a detail of 6 men to shoot it.
Can I? Can I? Please, please, pretty please >:D


-
I love this thread! :D I can't access FB on the work PC, and I'm too lazy to check on my phone, but were any of these results posted on his FB page?
A big thanks for taking the time to do these awesome tests, and taking lots of pics!!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login