Can This Be Fixed??
-
The bottom scale on the yellow rescue tool is not flush with the bolster,(just under driver/bottle opener, about 1/4 of the way in to the center of tool.) Should have sent it back, noticed this a few hours after I got it. but when wrist flicking the stiff new blade, it went flying into my balcony deck, and dinged the far left on top.
Anyway, I will use it at work, so not too worried, but looking for a suggestion on possibly gluing the scale down so it sits flush, any ideas??? Thanks, BB

-
I can't really see the problum in the pic. I am thinking you could remove the scale and see what is going on with it. I am sure others that know a lot more than i do will chime in.
Mike -
I'll put some more pics up in a few, was just being lazy and used pics from an older thread.
-
I can see what you mean - one of my SAKs has the scale slightly elevated like that (by a fraction of a mm). Its never fallen off though.
A bit of superglue under the scale should help - apply a small brushing of glue, then weigh the SAK down under a book for a few hours to allow for complete curing of the glue. A resinous glue could also be used, but leave it for longer to dry.
-
Some more pics, excuse the slight blur, I don't have a tripod:



-
Personally, I'd just leave it as it is.
-
@rp252 said:
I can see what you mean - one of my SAKs has the scale slightly elevated like that (by a fraction of a mm). Its never fallen off though.A bit of superglue under the scale should help - apply a small brushing of glue, then weigh the SAK down under a book for a few hours to allow for complete curing of the glue. A resinous glue could also be used, but leave it for longer to dry.
I was considering super glue, but not sure if it works on metal/plastic combo.
-
I can see what you mean - one of my SAKs has the scale slightly elevated like that (by a fraction of a mm). Its never fallen off though.
A bit of superglue under the scale should help - apply a small brushing of glue, then weigh the SAK down under a book for a few hours to allow for complete curing of the glue. A resinous glue could also be used, but leave it for longer to dry.
I was considering super glue, but not sure if it works on metal/plastic combo.
It does, but its not always the best. If you roughen the surfaces to be bonded with sandpaper first it helps strengthen the bond - especially that polished vic finish. Do you need to glue it though? It might be more trouble than its worth.
-
I can see what you mean - one of my SAKs has the scale slightly elevated like that (by a fraction of a mm). Its never fallen off though.
A bit of superglue under the scale should help - apply a small brushing of glue, then weigh the SAK down under a book for a few hours to allow for complete curing of the glue. A resinous glue could also be used, but leave it for longer to dry.
I was considering super glue, but not sure if it works on metal/plastic combo.
It does, but its not always the best. If you roughen the surfaces to be bonded with sandpaper first it helps strengthen the bond - especially that polished vic finish. Do you need to glue it though? It might be more trouble than its worth.
No, I dont need to do it, but it would be nice if it was in the condition I expected.
-
While I'm sure it's annoying, I'd be inclined to leave it too :)
-
I'd be a fool not to agree with the big cheeses around here on this topic :D, so I'll leave it be 
-
If I were you I'd try to use a heat gun to see if I can make the scale flat (heat up and put under weight), if not then use a toothpick to dab some superglue under the gap and put under weight.
-
@Blackbeard said:
I'd be a fool not to agree with the big cheeses around here on this topic :D, so I'll leave it be 
:D
I'd leave it myself but if it really bothers you then I'd pop the scale at the back pin and gently lift it (no point on disturbing the other fixing points). As others have suggested brush a bit of glue in the affected area, but also on the pin head should see it right.
-
i've had this on one sak, too
in my case, the middle part of the scale was just not sitting tight around the place where the scale should snap on.
i just put a towel ower the knife and persuaded the scale with a little hammer to go where it should and everything was fine.from what the pic says, it does not have to be a bent scale maybe its just not fitting the point to hold the scale.
i wish i could tell you in german ...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login