Structural Difference between Kf4 and CS4
-
-
So Mr W, if you unfold the center flathead screwdriver on your Kf4, do the other two flop out aways?
Well.........? ???
Not exactly flop, but the other two have no spring resistance. Likewise, if I pull out one of the side drivers, the center one doesn't have spring resistance. They don't flop out however. Great observation Bob!

-
A
mistakeunique collectable indeed!
-
Great. :-\
Now I gotta retire it and find another KF4 user... :ahhh
-
@Mr. Whippy said:
Great. :-\Now I gotta retire it and find another KF4 user... :ahhh
I have a KF4 like this too, with the two wider backsprings on each side. Mine is an older yellow one with "Leatherman USA" on the plier head. I also have a storm grey one with "Leatherman Tool" on the head that has the three thinner backsprings behind the flatheads.
-
@Mr. Whippy said:
Great. :-\
Now I gotta retire it and find another KF4 user... :ahhh
I have a KF4 like this too, with the two wider backsprings on each side. Mine is an older yellow one with "Leatherman USA" on the plier head. I also have a storm grey one with "Leatherman Tool" on the head that has the three thinner backsprings behind the flatheads.
Maybe that's an older design then? Anybody? Bueller? Bueller?.
???
-
Hmmm - not sure it's an age thing. I have a 0601 KF4 (USA) that has three springs on on side. 0601 is pretty much as old as the KF4 gets. I also have a 0901 with the USA ground out and an 0402 (TOOL).
They are all the same :)
-
DOH! I forgot to check the date code on mine... I'll try to do that this evening.
Maybe Mr. Whippy and I just happened to each get a KF4 from the same run, and they were out of the thin springs at the time?

-
It's as good a theory as I can come up with!
We need a few more people to contribute to this thread and see how unusual they actually are, although there's a distinct chance that we could be opening another, PST-like can of worms.
Great

-
@DaveK said:
It's as good a theory as I can come up with!We need a few more people to contribute to this thread and see how unusual they actually are, although there's a distinct chance that we could be opening another, PST-like can of worms.
Great

....and once you've opened a can of worms, the whole place begins to stink of frogs. BTDT.

-
-
Hmmm - not sure it's an age thing. I have a 0601 KF4 (USA) that has three springs on on side. 0601 is pretty much as old as the KF4 gets. I also have a 0901 with the USA ground out and an 0402 (TOOL).
They are all the same :)
My goofy-sprung KF4 has an 0601 date code also.
Weird...
My date code is 1090....

Seriously, mine's 0601 too.
-
Spooky. :o
-
Date code on mine is 0401. USA.
Two springs. Maybe they did the switch in June.
-
Hey! I was just thinking about this thread the other day! (but couldn't find it) I've got some juicy info and more pictures to post

But I have to leave right now for a party. :( But I'll be back in a bit......
-
These structural differences were always interesting to me. I mean, all Juice models have different arengements of tools, different backsprings (2 or 3), different pivot points of specific tools, like for instance on some the knife pivots around the plier pivot, on some around the screwdriver pivot. Very interesting tool indeed.
.
.
.
.
.Mr. Bob, is the party over yet? :D
-
It was such a great party, I almost forgot to come back here! :D
So anyhow, awhile back I bought this snazzy Leatherman pouch.....

....and inside, there were two sets of Juice tools. :)

I'm thinking this was a Salesman's kit, meant to show potential buyers what the (then new) Leatherman Juice series was all about....?
That's my guess anyhow.All five tools on the lower flap are dated 0401 on both handles, which is the earliest date code we've seen on any Juice. And all five of them have two thick backsprings on both handles.



The tools on the top flap are even more special. 8) Not only do they have the two thick backsprings on both handles, but they also have NO date codes. :-X And the LEATHERMAN PAT PEND stamping on the back was done in chem etch, instead of being stamped into the metal. (see below)

Same goes for the LEATHERMAN USA logo on the plier pivot. It was chem etched (on right below) instead of being cast in like all the ones that came after.

So anyhow, I think when Leatherman first started producing Juice tools in the spring of 2001, there were no thin backsprings made. Its just a theory of course, but maybe they didn't realize that they would need the three thin ones on one side until after production started, and someone started playing with the screwdrivers and said, "Oh crap............."

-
without the thin back springs, are there any problems?
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
