Friction forging
-
Friction Forging?
More like FICTION Forging!
Amirite!?
Sorry, just woke up. It seemed clever in my head.
-
-
We also tested the toughness of the blade, as well as the sharpness by chopping completely through a 2"x 4" board twice, then cutting through a free hanging rope multiple times with one swipe. Once again, the blade still shaved hair like a razor," Karwan said.
this seems quite amazing, since if true, it means the knife has good chopping ability, as well as cutting.
-
We also tested the toughness of the blade, as well as the sharpness by chopping completely through a 2"x 4" board twice, then cutting through a free hanging rope multiple times with one swipe. Once again, the blade still shaved hair like a razor," Karwan said.
this seems quite amazing, since if true, it means the knife has good chopping ability, as well as cutting.
Any well made differentially tempered knife can do that though. In fact that is part of the ABS master smith test.
@ryan1835 said:
friction forging sounds cool, i like friction welding myselfFriction welding is technically a forging process, so perhaps the process is similar (if it actually exists, of course)
@Raukodur said:
Unless all of these reviewers are either lying or naive knife users, the above quoted article seems to have good things to say about friction forged knives.A few things with this.
"Objective test results with hands-free equipment confirmed that the Friction Forged® blade edge lasts about 10 times longer than a standard (best processed) D2 steel blade," said.
Why has the entire results of this test been released then? Why no lab reports? Why no articles published in peer reviewed journals?
Friction Forging®, through dynamic molecular shearing, "creates steel grain structure so fine, that it can only be seen with the aid of a Scanning Electron Microscope at 80,000 magnification," said Dr. Sorensen with BYU's Mechanical Engineering Department. "Normally, heat-treated and tempered blade steel grain structure can easily be seen with a standard 1,000 power microscope, but after undergoing the Friction Forging® process, the grain structures cannot be seen unless an electron microscope is employed." Sorensen went on to say.
Perhaps it comes this fine, however if this is true then the will be no conventional methods to sharpen the knife back to its original sharpness.
-
since I have now got some free time, I am going to start some Ebay trading to make money, see if I can raise the amount needed for one of these without then having to feel guilty about it (unfortunately I am enamoured by the most expensive version - the Elan)
-
Quote
Friction Forging®, through dynamic molecular shearing, "creates steel grain structure so fine, that it can only be seen with the aid of a Scanning Electron Microscope at 80,000 magnification," said Dr. Sorensen with BYU's Mechanical Engineering Department. "Normally, heat-treated and tempered blade steel grain structure can easily be seen with a standard 1,000 power microscope, but after undergoing the Friction Forging® process, the grain structures cannot be seen unless an electron microscope is employed." Sorensen went on to say.Perhaps it comes this fine, however if this is true then the will be no conventional methods to sharpen the knife back to its original sharpness.
I dont see why this is true. There is no 'magic' about this process, all it does is make the blade edge of the knife harder than the spine. You sharpen up the hard knife edge to get a good cutting edge which holds its sharpness, while the less hard, more flexible spine allows the knife to take more punishment without breaking.
Sharpening the edge would just be like sharpening any other knife which had a similarly hard edge. Use a diamon file or whatever.
-
A diamond blade is a saw blade which has diamonds fixed on its base for cutting hard or abrasive materials. There are many types of diamond blade, and they have many uses, including cutting stone, concrete, asphalt, bricks, coal balls, glass, and ceramics in the construction industry; cutting semiconductor materials in the IT industry; and cutting gemstones, including diamonds, in the gem industry.
Mods note: I removed the link but left the message intact.
-
@collantjay said:
A diamond blade is a saw blade which has diamonds fixed on its base for cutting hard or abrasive materials. There are many types of diamond blade, and they have many uses, including cutting stone, concrete, asphalt, bricks, coal balls, glass, and ceramics in the construction industry; cutting semiconductor materials in the IT industry; and cutting gemstones, including diamonds, in the gem industry.Mods note: I removed the link but left the message intact.
I haven't banned the user, but removed a link in this post. I don't see how this pertains to the thread. I'd like to hear how it applies before doing anything further. Collantjay?
-
It's just random spam. This type seems to be more common lately, less blatant and post in thread with certain keywords (like the URL in OP), with links to whatever they are selling.
-
SFS flagged the IP of the user... account rejected.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login