None Riveted Construction?
-
Hey guys, I plan on taking my dad's huntsman apart for some much need cleaning and oiling. Over the years, dirt and debris have been collecting on in its insides and it's not far from needing a pair of pliers to open it. I'll be ordering the brass rod very soon, but in the mean time, I won a couple of used 91mm SAKs on ebay. I've already received and taken one apart. I don't have any metric drill bits so I used a 5/64 bit and went slow. In the end, I did hit the inside of two of the bushings, but didn't do any major damage. Upon closer examination, the hole on the bottom of the bushing that touches the aluminum liner was left untouched.
Anyway, after much searching on in this forum as well as the web I've got several ideas on how I might reassemble this SAK. The cheapest solution, by far, is simply put it back together like I got it. Another idea I have is to replace the three rivets with bushing with adjustable pivots like my delica 4 has. The smallest pivots I can find are an 1/8th of an inch in diameter and the longest are half an inch long. With the 1/8th inch wide, half inch pivots, I figure I can put them in a four tool wide SAK, but that’s the absolute limit. I was thinking of putting bronze washers between the tools, but their added thickness would limit them to a three tool wide SAK and it would be a bit awkward considering what the internals are like. Right now, bronze washers aren’t important.
Getting back to my idea concerning adjustable pivots, this would require the holes except those on the corkscrew side to have their holes widened. The back springs would need the gaps that the brass rod runs through widened as well. The tools on the corkscrew side wouldn’t be riveted, but would have a pin that floats snugly in their holes and held in by the liners with the tension from the nearby pivot. Something else I may need to do, although this may not be a must, is make new scales. The red plastic ones have holes that the three bushings are pressed and bite into. Since there won’t be any bushings, these are largely unneeded.
So, do I make new scales are reused the old ones? Two ideas I have both involve resin. The first is to make new scales via the DIY micarta method which I wouldn’t mind trying anyway. Once they were done, I’d salvage the crest and make a single hole in one of the new scales just big enough for the crest to rest in. It would be just slightly deeper than the crest is thick. After making sure the crest was square, I’d fill the hole it sits in with resin to protect it. My second idea is to fill the all the cavities in the current scales with resin. I’d drill holes through the scales for the screws and countersink them as well.
Again, these are just a couple of ideas I have and I’d like to hear your thoughts.
-
Finding small enough pivot barrels has been something that has stopped people from putting together a more easily disassembled SAK :-\
Widening the holes at the tool ends to accept 1/8" barrels shouldn't cause any great issues but I'm not so sure about the lack of riveting of the centre pins. I wonder if sideways forces on the tools and backsprings especially during opening and closing might be problematic. Perhaps if you were to have the outside liners made from something with a little less flex?
I'd go with making new scales rather than reusing the originals. Firstly because you could make them from something stiff like G10 helping with the mid pin issue and also because different is always good :)
At the end of the day used SAKs are pretty cheap so go for it and experiment. Just so long as you post pics and let us know how it goes
:D -
There's a WIP I would LOVE to follow!
-
Talk about reviving an dead thread. I finally did it. It's not perfect, but I don't consider this done. Maybe this could be considered version 1? There are still things that need to be fixed, but it's together and working for the most part. Here are some pictures. I hope you enjoy them.





-
Drilling the tools out to 1/8" is actually quite difficult. I use a precision drill press and carbide spade drills and it still makes my teeth hurt just thinking about it. If you're going to do this as a hobby then it might be worth setting up for that but if you just want the easiest way to get this particular SAK back up and running then the peening on 91s is not too difficult. It doesn't have to be pretty like the Alox peening as long as the bushings are in good enough shape to hold it together.
-
It was no fun drilling the holes. That much I can say. It would have been much easier if I had a better drill press and even a vise for it. I think my lack of experience was also a factor as well. LOL
Overall, I'm not dissatisfied with how it came out. I think this was more of a proof of concept. It's fully functional, but because it's not riveted, the back tools have lost most of their strength. This doesn't bother me as much since I can't say I have ever used them. I've also heard of the rivets breaking and the tool twisting.
Another issue that I need to solve is the snap the tools have on a regular SAK. This one is soft. They open and lock fine, but it's not what it could be. My guess is that the two brass rods don't quite go all the way through to the last aluminum scale. You can see this in the last two pictures. I need to find some replacement brass rod that will go through all the way for the two middle rivets.
One last problem that needs to be addressed is the flex that's in the outer plastic scales. When using the back tools, the outer plastic scales will bow outward. Right now, I believe the problem is exaggerated because of the above issue, but they need to be replaced with something stiffer. Aluminum or steel would work most likely, but I don’t know about micarta or some other synthetic material?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login