Pivot Tightening Question
-
I've got my brand new Charge TTi in the mail which is in absolutely pristine condition. The only thing I've noticed, which doesn't bother me much although i'd still like to fix it, is that the tools inside the serrated knife handle (the removable bit and can opener) are a bit loose since they come out very easily if shake the tool abruptly. The tools inside the opposite handle have just the right amount of resistance when opening.
Now I've heard a common remedy is to tighten the pivots slightly yourself if you have the T-10 Torx, however, won't this destroy the effectiveness of the loctite, if you move them from their initially set place in the thread, even a fraction of a revolution as in this case? Or once there is Loctite on the thread, it's still as effective wherever you set the bolts at? I just don't know/ don't want the screw to loosen more easily over time because I've broken the seal, even though I've tightened them, compared to not having tightened them at all.Thanks guys
-
First off only one screw will turn , this is because the other one isnt round and fits in the hole and wont turn ..So first off you need to find which one to tighten . I would use a mangifying glass and look reall carefully and youll notice that one of the screw heads has very slight flat sides , don't turn this one . You may also find that because of the loctite you may not be able to budge the screw at all and will need to heat it . I use a candle but you could use a soldering iron held on the screw head . You need to heat it to about 200c . Don't worry about cracking the bond , it should redarden .
I would think carefully about it before you do it . You could always send it to leatherman .
oh and welcome to the forum .
Dunc
-
I have found that if you just tighten the pivot screw to your desired torque you won't generally have a problem with it coming loose. Yes, if you tighten or loosen, the loctite seal will break, however in practice if you tighten I found that it will not loosen itself during normal use. You have nothing to lose to tighten and periodically check it to make sure the inside implements haven't loosened up which would indicate that the pivot screw was loosening. I have tightened many a Charge that way and haven't had a problem with the pivot screw loosening on it's own. Even if you don't reapply the loctite after tightening the pivot screw the presence of the loctite on the screw will tend to keep it in place.
To be on the safe side however you are better off removing the pivot screw, cleaning it and then reapplying some Loctite blue http://www.loctiteproducts.com/p/t_lkr_blue/overview/Loctite-Threadlocker-Blue-242.htm
I would recommend tightening it as the loose implements would bother me. It should only take a very small amount of turning to tighten it up.
-
If you have the t10 security torx ( you need two ) one to hold one side in place and you turn the other, its easy to do. I would first tighten to your likeing and if it comes loose again, you can buy a tube of locktite, remove the screw and reset it. Or you could send it in to leatherman and they will fix it.
Im too slow. already answered. :D -
Thanks guys, and yes I will be careful and am aware at only one screw will turn; to my knowledge and from previous disassembles, the screw opposite the knife blade (whether clip point or serrated) is actually a screw. What goes through the knife blades is the long pivot itself, which I plan on keeping fixed with counter pressure. Can anyone back me up on this?
Thx -
@Mr.Dude said:
Thanks guys, and yes I will be careful and am aware at only one screw will turn; to my knowledge and from previous disassembles, the screw opposite the knife blade (whether clip point or serrated) is actually a screw. What goes through the knife blades is the long pivot itself, which I plan on keeping fixed with counter pressure. Can anyone back me up on this?
ThxI use 2 Torx bits, one on a small ratchet for the screw, and the backside I hold still with a fixed screwdriver with a Torx bit. This way I don't have to rely on tool to hold the pivot in place.
-
I can't answer your question, because I don't know the answer, but I would unscrew the whole thing and apply new loctite.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login