Titanium SAK progress...
-
@bushidomosquito said:
Meh, they could be better but thanks. :) They are 3 pieces, 5 if you count the 2 rivet pins. I cut them out of .030" sheet, epoxied them together, drilled 2 holes for the rivets, broke everything apart and finish sanded and tweaked the slight bends, riveted them together, sanded the rivets flush, shaped the grabby end aaaaaaand rounded the head. They should have been .020 sheet so they would fit in a standard cellidor slot depth but they sure do hold tight. You can sort of make out where the 2 rivets hold the 2 pieces of the toothpick together.Wow.

-
Meh, they could be better but thanks. :) They are 3 pieces, 5 if you count the 2 rivet pins. I cut them out of .030" sheet, epoxied them together, drilled 2 holes for the rivets, broke everything apart and finish sanded and tweaked the slight bends, riveted them together, sanded the rivets flush, shaped the grabby end aaaaaaand rounded the head. They should have been .020 sheet so they would fit in a standard cellidor slot depth but they sure do hold tight. You can sort of make out where the 2 rivets hold the 2 pieces of the toothpick together.
Wow.

x10

-
I didn't notice the rivets until you mentioned it. Very meticulous work

-
Meh, they could be better but thanks. :) They are 3 pieces, 5 if you count the 2 rivet pins. I cut them out of .030" sheet, epoxied them together, drilled 2 holes for the rivets, broke everything apart and finish sanded and tweaked the slight bends, riveted them together, sanded the rivets flush, shaped the grabby end aaaaaaand rounded the head. They should have been .020 sheet so they would fit in a standard cellidor slot depth but they sure do hold tight. You can sort of make out where the 2 rivets hold the 2 pieces of the toothpick together.
Wow.

x10

+1 amazing work!! congrats

-


Carbon fiber and orange G10 with hardware to space the liners apart for finish sanding. -
OOOO pretty!
I can't wait for you to work some magic on my G10 scales!
-
Bushi you did not make those wee Torx like fasteners did you
.If , I know slim chance you didn't make them :ahhh :ahhh :D :D, were did ya gets them from
8) 8) 8). -
@MultiMat said:
Bushi you did not make those wee Torx like fasteners did you
.If , I know slim chance you didn't make them :ahhh :ahhh :D :D, were did ya gets them from
8) 8) 8).http://www.usaknifemaker.com/folding-knife-parts-c-30.html?zenid=5242c1d84b4bea6378a9bd1b8d1f9747
-
Bushi you did not make those wee Torx like fasteners did you
.If , I know slim chance you didn't make them :ahhh :ahhh :D :D, were did ya gets them from
8) 8) 8).http://www.usaknifemaker.com/folding-knife-parts-c-30.html?zenid=5242c1d84b4bea6378a9bd1b8d1f9747
Mate , saved too Bookmarks + they do international shipping 8) 8) 8) -
[quote
I can't wait for you to work some magic on my G10 scales!
[/quote]I hope they show up today. I could use a distraction for a few hours.
-
Oh no, they won't show up for at least a week. I just dropped them off in the mail today.
-
I've been up all night putting this together. Still have to sand the rivets down flush and polish the sides. Soooooo close...





-
Fantastic!

-
That's a thing of beauty :o

-

Seriously, that looks amazing!
-
Gorgeous mate, simply gorgeous.
Are you using little washers between the springs/tools and the liners? -
The amazingness, it boggles the mind!!! :ahhh :ahhh :ahhh

-
The aluminum liners have stamped raised areas to keep the tools from rubbing on them so I made phosphor bronze washers with a little stamping fixture that I also made. That blade is one of the thicker pre '07 ones with the crossbow stamp and was a little scratched so it got hand rubbed down to 2000 grit and Flitz polished. The only marks on it are the ever present fingerprints.

The holes are punched out of .005" phosphor bronze strips and then cut into squares which get stacked onto a dremel sanding drum mandrel and run against a belt sander until they are all round and the same diameter. Then they get run against 320 and 600 grit silicon carbide paper until the edges are polished.

The pliers layer before washers are applied, and my little orange G10 and titanium Classic that I made the titanium tweezers and toothpick for in the background.

Final opener layer. The 1/8" hole washers fit perfectly onto a sanding drum shaft and the smaller back tool washers fit the threaded portion of the screw on the end of the shaft so it works out very well.

-
And thank you all for
ing and :ahhh :ahhh :ahhh ing all over my knife. Showing off is half the fun. -
that is very nice.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login