Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Sidekick wire cutters

Scheduled Pinned Locked Moved Leatherman Tools
10 Posts 1 Posters 5.1k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. Sidekick wire cutters
Sidekick wire cutters
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Dunc Offline
    Dunc
    Admin Team
    Posts: 11,308
    Dunc Offline
    Dunc
    Admin Team
    wrote on last edited by
    Quote Reply

      When you look at the user guide for the Sidekick it doesn't mention a hard cutter but on the tool there is clearly a notch at the base of the cutters . The photos on the LM website do not show this notch :think: Its also too large for most hard wire and serves little purpose unless its for wire stripping which I havn't tried yet .
      Whilst on the subject of wire cutters also note how the cutters don't meet when the pliers are closed but do when the handles are squeezed. The are however very effective at cutting thin wire and paper clips as well as twin core cable ( 240V) .

      Just thought I'd share .

      1 Reply Last reply
      • sawman Offline
        sawman
        Posts: 9,745
        sawman Offline
        sawman
        wrote on last edited by
        #1 Quote Reply

          That does make me feel better about the wire cutters. On the Octane, they were actually crooked and I could not get them to cut, but it's good to know LM put a little more precision into it.

          1 Reply Last reply
          • J-sews Offline
            J-sews
            Admin Team
            Posts: 23,224
            J-sews Offline
            J-sews
            Admin Team
            wrote on last edited by
            #2 Quote Reply

              I've had quite good results cutting a variety of copper wire with my Sidekick. :salute: Haven't tried any steel wire yet, but there's a coat hanger out in the garage that is begging to be chopped up. :)

              1 Reply Last reply
              • Bruce909 Offline
                Bruce909
                Posts: 613
                Bruce909 Offline
                Bruce909
                wrote on last edited by
                #3 Quote Reply

                  Bob,

                  You need to make a fixture to hold the tool and then put your boot on the top handle....or wait I kinda have deja vu.

                  Bruce

                  1 Reply Last reply
                  • J-sews Offline
                    J-sews
                    Admin Team
                    Posts: 23,224
                    J-sews Offline
                    J-sews
                    Admin Team
                    wrote on last edited by
                    #4 Quote Reply

                      @Bruce909 said:
                      Bob,

                      You need to make a fixture to hold the tool and then put your boot on the top handle....or wait I kinda have deja vu.

                      Bruce

                      Hah! :D

                      Now if only I knew someone who had such a fixture...? :think:

                      :D

                      1 Reply Last reply
                      • turnsouth Offline
                        turnsouth
                        Posts: 2,538
                        turnsouth Offline
                        turnsouth
                        wrote on last edited by
                        #5 Quote Reply

                          Juli's comments on the notch:

                          "WHAT IS THAT SMALL NOTCH AT THE BOTTOM OF THE SK AND WM WIRE CUTTERS :: A bunch of you have asked and no they are not hard-wire cutters so here is the answer I got from engineering, "The notch is for stress relief, to make the jaw stronger. Because the two halves of the jaw are coming together there, you need a relief to transition to the coined/sliding contact area. Take a close look and you'll see that to go from sliding contact at the pivot to cutter contact at the cutter tips, you need some kind of clearance allow that to happen without interference. It's just coincidental that it looks like a hard wire cutter.""

                          and:

                          "Wire stripper on the SK and WM is on the base of the can/bottle opener. Wouldn't recommend using hard-wire cutting on the SK and WM cutters or you'll tweak your pliers out of alignment. Juli@Leatherman"

                          1 Reply Last reply
                          • J-sews Offline
                            J-sews
                            Admin Team
                            Posts: 23,224
                            J-sews Offline
                            J-sews
                            Admin Team
                            wrote on last edited by
                            #6 Quote Reply

                              Makes sense. :salute:

                              1 Reply Last reply
                              • scrappy Offline
                                scrappy
                                Posts: 2,633
                                scrappy Offline
                                scrappy
                                wrote on last edited by
                                #7 Quote Reply

                                  I wonder if the wave needs the stress release point?

                                  1 Reply Last reply
                                  • J-sews Offline
                                    J-sews
                                    Admin Team
                                    Posts: 23,224
                                    J-sews Offline
                                    J-sews
                                    Admin Team
                                    wrote on last edited by
                                    #8 Quote Reply

                                      @scrappy said:
                                      I wonder if the wave needs the stress release point?

                                      There's probably some that could have benefitted from it :salute: :D

                                      1 Reply Last reply
                                      • captain spaulding Offline
                                        captain spaulding
                                        Posts: 20,793
                                        captain spaulding Offline
                                        captain spaulding
                                        wrote on last edited by
                                        #9 Quote Reply

                                          @J-sews said:

                                          @scrappy said:

                                          I wonder if the wave needs the stress release point?

                                          There's probably some that could have benefitted from it :salute: :D

                                          :rofl: :rofl: :rofl:

                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          1. Home
                                          2. Tool Talk
                                          3. Leatherman Tools
                                          4. Sidekick wire cutters
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0