Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Torx driver?

Scheduled Pinned Locked Moved Keychain and One Piece Tools
13 Posts 1 Posters 5.3k Views
  1. Home
  2. Tool Talk
  3. Keychain and One Piece Tools
  4. Torx driver?
Torx driver?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Cloud Cleaver Offline
    Cloud Cleaver
    Posts: 3
    Cloud Cleaver Offline
    Cloud Cleaver
    wrote on last edited by
    Quote Reply

      I've been hunting for a slim, quality Torx driver for my keychain. Specifically I need T6, T7, T9 and T10 to maintain my Zero Tolerance knives when I'm away from home. I figured there'd be a lot of options, but I've only managed to find two. One is from Kershaw and the other is from CRKT; neither have all the bits I need and both seem a little poor in quality. Do you know of another way to get the bits I need into a minimalist keychain setup?

      1 Reply Last reply
      • Sazabi Offline
        Sazabi
        Posts: 6,397
        Sazabi Offline
        Sazabi
        wrote on last edited by
        #1 Quote Reply

          This might be a stupid question, but take one of these, which is much cheaper at Home Depot, at $6, and maybe find something that could turn the bits? Unless it has to stay on your keychain, you could slip it into a bag, no worries.

          1 Reply Last reply
          • enki_ck Offline
            enki_ck
            Global Moderators
            Posts: 20,936
            enki_ck Offline
            enki_ck
            Global Moderators
            wrote on last edited by
            #2 Quote Reply

              I think anything you might find would be to big for a keychain or if keychain sized, not enough torque. The only keychain tool that would be ok is that Screwpop tool, but you than have to carry your bits separatly.

              I for one would choose one that comes in a charter members care package, a bit holder and screwdriver in one. I know benchmade makes something like it called the blue box but ours is better. :D

              /post/568536

              1 Reply Last reply
              • nuphoria Offline
                nuphoria
                Admin Team
                Posts: 15,038
                nuphoria Offline
                nuphoria
                Admin Team
                wrote on last edited by
                #3 Quote Reply

                  Keychain might be hard to find, but carrying a SAK Cybertool would be useful :)

                  1 Reply Last reply
                  • Sazabi Offline
                    Sazabi
                    Posts: 6,397
                    Sazabi Offline
                    Sazabi
                    wrote on last edited by
                    #4 Quote Reply

                      @nuphoria said:
                      Keychain might be hard to find, but carrying a SAK Cybertool would be useful :)

                      Except for the bits needed include some of the harder-to-find ones that Neil and maybe one or two other people can get. Also, needing T6 through T10, I don't think a T7 was made for the bit driver, was it? It's not listed on SAKwiki.

                      1 Reply Last reply
                      • Cloud Cleaver Offline
                        Cloud Cleaver
                        Posts: 3
                        Cloud Cleaver Offline
                        Cloud Cleaver
                        wrote on last edited by
                        #5 Quote Reply

                          I hadn't thought of a SAK. Further research has turned up three options, though. First is the handmade (and difficult to find) Jordan Metal Micro Bit Twist. Next is the Topeak Toolbar, which takes 1/4 hex bits but I'd have to file them to fit. Last is the EDC key. Very affordable way to pack a single bit, but it seems a little long. Thoughts on these options?

                          http://jordanmetalart.blogspot.com/2011/07/micro-bit-twists.html?m=1
                          http://www.topeak.com/products/Tools/ToolBar
                          http://countycomm.com/edckey.html

                          1 Reply Last reply
                          • Farmman Offline
                            Farmman
                            Posts: 911
                            Farmman Offline
                            Farmman
                            wrote on last edited by
                            #6 Quote Reply

                              If you don't mind carrying the hex bits seperate look at the tt pocket tools in the thread below. The wife has the skull one which I think would do you nicely.

                              1 Reply Last reply
                              • enki_ck Offline
                                enki_ck
                                Global Moderators
                                Posts: 20,936
                                enki_ck Offline
                                enki_ck
                                Global Moderators
                                wrote on last edited by
                                #7 Quote Reply

                                  @Cloud Cleaver said:
                                  Last is the EDC key. Very affordable way to pack a single bit, but it seems a little long. Thoughts on these options?

                                  http://countycomm.com/edckey.html

                                  Compact Screwdrivers (Screw Pop VS. TorqKey)

                                  1 Reply Last reply
                                  • frugalscotty Offline
                                    frugalscotty
                                    Posts: 305
                                    frugalscotty Offline
                                    frugalscotty
                                    wrote on last edited by frugalscotty
                                    #8 Quote Reply

                                      I'll second Sazabi's suggestion of the Husky 8-in-1 set. I picked up one of these for six bucks at HD and I think it is well worth it.

                                      Also you said you only needed T6 7 9 10. The set I have has T4 and T15 on opposite ends of the same bit. You could leave that bit at home and just carry the other three bits inside the handle for safe keeping and this would also shorten the package by .75 inch. That would give you T5 6 7 8 9 10 in a 4.75 inch package.

                                      Easily replaceable if lost too.

                                      1 Reply Last reply
                                      • allyourblood Offline
                                        allyourblood
                                        Posts: 40
                                        allyourblood Offline
                                        allyourblood
                                        wrote on last edited by allyourblood
                                        #9 Quote Reply

                                          Sorry for bumping a slightly old thread, but I didn't see it until today. Considering the size of some of these suggestions, you almost might just got with a folding torx solution like the following:

                                          http://www.harborfreight.com/7-pc-mni-star-tamper-proof-key-set-97469.html

                                          It's also a tamper-proof set so you're good to go if you run into that type of screw sometime down the road.

                                          For ultimate portability, you can even unscrew the thing entirely and just put the drivers you need on your keyring, directly. The loop at the end will likely provide enough torque for adjusting knives, anyway.

                                          1 Reply Last reply
                                          • hugh_h Offline
                                            hugh_h
                                            Posts: 76
                                            hugh_h Offline
                                            hugh_h
                                            wrote on last edited by
                                            #10 Quote Reply

                                              A couple points:

                                              -I design electronics packaging. If there's something that screws together, I almost always use Torx. We used to use hex screws, but an internal drive is easier to automatically feed. On top of that, a Torx drive is superior to, say, a Phillips head because the angles on the Phillips tend to "cam out" the driver. That is, the harder you turn the screwdriver, the more force to push the driver out of the drive form. Torx tools last longer--not a big deal if you tighten/loosen 30 things per year, but rather inportant if you do 30 per minute on an assembly line.

                                              -That Harbor Freight tool is interesting, especially because it's for "Tamper-Proof" screws. Obviously, they're not Tamper-PROOF, because someone's tampering with them. We call that tamper-resistant. That's because an ingenious person can tamper with anything, and all we can do is "resist." For Tamper-PROOF design, I looked at dispensing an acrylic into the screw's counterbore after assembly, and covering the screw head with special tape that's got sctrong glue and weak paper, so it tears when you try to remove it to get at the screw head. When I asked the other engineers to see if they could defeat these measures, one guy chipped out the acrylic, then replaced it be melting with a soldering gun. So, it was not only far from Tamper-PROOF, it wasn't even tamper-evident. A sharp razor blade and lots of patience can remove one of those special anti-tamper labels too. (Now, with plastic hosuings, I use Ultrasonic or LASER welding to seal up the case.)

                                              -As much as I've used my two-dozen knives/multi-tools/keychain tools, for a real job I get a real tool. Anything can unscrew a computer case screw or something like that, but stuff that's out doors or on a car needs a good tool. I've seen SAKs ruined because of applying torque to the assembly of blades/springs/tools, etc., when a dedicated driver would have been the better choice. One isn't always available, though.

                                              1 Reply Last reply
                                              • Gryffin Offline
                                                Gryffin
                                                Posts: 480
                                                Gryffin Offline
                                                Gryffin
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  I use that Husky 8-in-1 driver (as well as one in flat/phillips) and it's GRATE for working on knives, lights, and electronics. :tu:

                                                  1 Reply Last reply
                                                  • Metropolicity Offline
                                                    Metropolicity
                                                    Posts: 3,797
                                                    Metropolicity Offline
                                                    Metropolicity
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      KEYCHAIN!

                                                      I just ran into this last night:

                                                      http://www.crkt.com/Get-a-Way-Driver-Torx-Set

                                                      1 Reply Last reply

                                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                      With your input, this post could be even better 💗

                                                      Register Login

                                                      1. Home
                                                      2. Tool Talk
                                                      3. Keychain and One Piece Tools
                                                      4. Torx driver?
                                                      Reply
                                                      • Reply as topic
                                                      Log in to reply
                                                      COMMUNITY LINKS
                                                      EDC-TV SAKWiki GearFeed SAKSelector
                                                      Operational Funds

                                                      Help us keep the Unworkable working!

                                                      Make A Donation
                                                      November Goal: $300.00
                                                      Due Date: Nov 30
                                                      Total Receipts: $0.00
                                                      Below Goal: $300.00
                                                      0% funded
                                                      • Login

                                                      • Don't have an account? Register

                                                      • Login or register to search.
                                                      • First post
                                                        Last post
                                                      0