Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Sissors spring question

Scheduled Pinned Locked Moved Swiss Army Knights Forum
13 Posts 1 Posters 1.5k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Sissors spring question
Sissors spring question
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • enki_ck Offline
    enki_ck
    Global Moderators
    Posts: 20,936
    enki_ck Offline
    enki_ck
    Global Moderators
    wrote on last edited by
    #2 Quote Reply

      There are four sizes. Small for 58mm, large for modern 91mm. But there are also specific springs for 74mm and a different size again for 84mm and old 91mm. You can modify the modern 91mm spring though to fit the 84mm scissors.

      1 Reply Last reply
      • Syph007 Offline
        Syph007
        Global Moderators
        Posts: 9,842
        Syph007 Offline
        Syph007
        Global Moderators
        wrote on last edited by
        #3 Quote Reply

          @enki_ck said:
          There are four sizes. Small for 58mm, large for modern 91mm. But there are also specific springs for 74mm and a different size again for 84mm and old 91mm. You can modify the modern 91mm spring though to fit the 84mm scissors.

          The only 84s Ive seen also use the older style spring that is curved at the end and not the modern style that is pointed and rides in the little groove on the scissor handle. Modern 91s are just a tiny bit bigger than the old 84's, so they should be able to be modified fine to work.

          1 Reply Last reply
          • Gareth Offline
            Gareth
            Admin Team
            Posts: 37,725
            Gareth Offline
            Gareth
            Admin Team
            wrote on last edited by
            #4 Quote Reply

              IIRC the little 'curl' that fits into the body of the scissors is notably smaller on the 84mm spring compared to the 91mm one. I've never tried modding one myself so I'd be interested in hearing how others have done it. :)

              1 Reply Last reply
              • enki_ck Offline
                enki_ck
                Global Moderators
                Posts: 20,936
                enki_ck Offline
                enki_ck
                Global Moderators
                wrote on last edited by
                #5 Quote Reply

                  Here's a 91mm spring next to 84mm scissors with modified spring. Not the best looking job, but it works great.

                  1 Reply Last reply
                  • tattoosteve99 Offline
                    tattoosteve99
                    Posts: 6,326
                    tattoosteve99 Offline
                    tattoosteve99
                    wrote on last edited by
                    #6 Quote Reply

                      I just crimp the round in a little. Using a 1/16 punch and tap lightly into place.

                      1 Reply Last reply
                      • enki_ck Offline
                        enki_ck
                        Global Moderators
                        Posts: 20,936
                        enki_ck Offline
                        enki_ck
                        Global Moderators
                        wrote on last edited by
                        #7 Quote Reply

                          The info on the springs comes from Neil and if you need springs for 84mm scissors, he has them, they just aren't listed on edcsource so you'll have to PM him.

                          1 Reply Last reply
                          • sergemaster Offline
                            sergemaster
                            Posts: 1,058
                            sergemaster Offline
                            sergemaster
                            wrote on last edited by
                            #8 Quote Reply

                              Amici,
                              I recall when I had ro replace the spring on my 20 + year Swisschamp, I found some doc online at the time that turned out to be quite helpful for a pretty painless procedure. Picked up my springs from Rotokid a few years back plus some.

                              Cheers,
                              Serge

                              1 Reply Last reply
                              • J Mackrel Jones Offline
                                J Mackrel Jones
                                Posts: 731
                                J Mackrel Jones Offline
                                J Mackrel Jones
                                wrote on last edited by
                                #9 Quote Reply

                                  Instructions from The Swiss Army Knife Owner's Manual:
                                  "Pull out the scissors (or pliers) half-way, so that the hole in the
                                  fixed arm is well clear of the body of the knife. Put the knife on its side on
                                  a table. Support the scissor-arm with something about the same thickness
                                  as the height that the scissor is off the table, like a pencil or several coins.
                                  Put this support close to, but not right under, the spring-hole, which is filled
                                  right now with the circle-end of the broken spring. Get an awl or find a nail
                                  with a tip just larger than the hole in the center of the spring-end, but
                                  smaller in diameter than the hole in the scissors. Hold its point in the center
                                  of the circular spring-end and tap the head of the nail straight down
                                  with a hammer. Light taps will do it. The support prevents bending the
                                  scissors and keeps the hammer-taps solid. And so drive the broken spring
                                  out of its hole. If you’re careful you won’t drive the end of your small pointy
                                  tool into the top of the table.
                                  The circle-end of the new spring should be just a little too big to go
                                  into the hole; it will be a press-fit. Slide the straight section near the base
                                  of the spring into the slot between the hole and the shaft of the scissor-arm
                                  and start the circle at an angle partway in the hole, starting with the opening
                                  in the circle. Hold it in this position with a pliers and squeeze as you
                                  rock the pliers and spring into line." (with photo)

                                  1 Reply Last reply
                                  • Syph007 Offline
                                    Syph007
                                    Global Moderators
                                    Posts: 9,842
                                    Syph007 Offline
                                    Syph007
                                    Global Moderators
                                    wrote on last edited by
                                    #10 Quote Reply

                                      The only tools ive used to swap spring is my vic huntsman. Awl to push out old spring, and then the side of a big tool like the bottle opener to push the new spring home with. Pliers would likely be easier though.

                                      1 Reply Last reply
                                      • demonoflust Offline
                                        demonoflust
                                        Posts: 243
                                        demonoflust Offline
                                        demonoflust
                                        wrote on last edited by
                                        #11 Quote Reply

                                          @enki_ck said:
                                          The info on the springs comes from Neil and if you need springs for 84mm scissors, he has them, they just aren't listed on edcsource so you'll have to PM him.

                                          I would love to, but will Neil ship to Singapore? Not sure if the shipping cost is going to be expensive.

                                          1 Reply Last reply
                                          • enki_ck Offline
                                            enki_ck
                                            Global Moderators
                                            Posts: 20,936
                                            enki_ck Offline
                                            enki_ck
                                            Global Moderators
                                            wrote on last edited by
                                            #12 Quote Reply

                                              @demonoflust said:

                                              @enki_ck said:

                                              The info on the springs comes from Neil and if you need springs for 84mm scissors, he has them, they just aren't listed on edcsource so you'll have to PM him.

                                              I would love to, but will Neil ship to Singapore? Not sure if the shipping cost is going to be expensive.

                                              His shipping is very reasonable and he ships most places. Why not send him a PM here and ask for a shipping quote.

                                              404 Not Found

                                              favicon

                                              (forum.multitool.org)

                                              1 Reply Last reply

                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                              With your input, this post could be even better 💗

                                              Register Login

                                              1. Home
                                              2. Tool Talk
                                              3. Swiss Army Knights Forum
                                              4. Sissors spring question
                                              Reply
                                              • Reply as topic
                                              Log in to reply
                                              COMMUNITY LINKS
                                              EDC-TV SAKWiki GearFeed SAKSelector
                                              Operational Funds

                                              Help us keep the Unworkable working!

                                              Make A Donation
                                              November Goal: $300.00
                                              Due Date: Nov 30
                                              Total Receipts: $0.00
                                              Below Goal: $300.00
                                              0% funded
                                              • Login

                                              • Don't have an account? Register

                                              • Login or register to search.
                                              • First post
                                                Last post
                                              0