Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Sissors spring question

Scheduled Pinned Locked Moved Swiss Army Knights Forum
13 Posts 1 Posters 1.5k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Sissors spring question
Sissors spring question
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • demonoflust Offline
    demonoflust
    Posts: 243
    demonoflust Offline
    demonoflust
    wrote on last edited by
    Quote Reply

      Hi, is the scissors spring on 91mm and 84mm interchangeable?

      1 Reply Last reply
      • macabee Offline
        macabee
        Posts: 355
        macabee Offline
        macabee
        wrote on last edited by
        #1 Quote Reply

          I don't think so, as there are two separate sizes available :salute:

          1 Reply Last reply
          • enki_ck Offline
            enki_ck
            Global Moderators
            Posts: 20,936
            enki_ck Offline
            enki_ck
            Global Moderators
            wrote on last edited by
            #2 Quote Reply

              There are four sizes. Small for 58mm, large for modern 91mm. But there are also specific springs for 74mm and a different size again for 84mm and old 91mm. You can modify the modern 91mm spring though to fit the 84mm scissors.

              1 Reply Last reply
              • Syph007 Offline
                Syph007
                Global Moderators
                Posts: 9,842
                Syph007 Offline
                Syph007
                Global Moderators
                wrote on last edited by
                #3 Quote Reply

                  @enki_ck said:
                  There are four sizes. Small for 58mm, large for modern 91mm. But there are also specific springs for 74mm and a different size again for 84mm and old 91mm. You can modify the modern 91mm spring though to fit the 84mm scissors.

                  The only 84s Ive seen also use the older style spring that is curved at the end and not the modern style that is pointed and rides in the little groove on the scissor handle. Modern 91s are just a tiny bit bigger than the old 84's, so they should be able to be modified fine to work.

                  1 Reply Last reply
                  • Gareth Offline
                    Gareth
                    Admin Team
                    Posts: 37,725
                    Gareth Offline
                    Gareth
                    Admin Team
                    wrote on last edited by
                    #4 Quote Reply

                      IIRC the little 'curl' that fits into the body of the scissors is notably smaller on the 84mm spring compared to the 91mm one. I've never tried modding one myself so I'd be interested in hearing how others have done it. :)

                      1 Reply Last reply
                      • enki_ck Offline
                        enki_ck
                        Global Moderators
                        Posts: 20,936
                        enki_ck Offline
                        enki_ck
                        Global Moderators
                        wrote on last edited by
                        #5 Quote Reply

                          Here's a 91mm spring next to 84mm scissors with modified spring. Not the best looking job, but it works great.

                          1 Reply Last reply
                          • tattoosteve99 Offline
                            tattoosteve99
                            Posts: 6,326
                            tattoosteve99 Offline
                            tattoosteve99
                            wrote on last edited by
                            #6 Quote Reply

                              I just crimp the round in a little. Using a 1/16 punch and tap lightly into place.

                              1 Reply Last reply
                              • enki_ck Offline
                                enki_ck
                                Global Moderators
                                Posts: 20,936
                                enki_ck Offline
                                enki_ck
                                Global Moderators
                                wrote on last edited by
                                #7 Quote Reply

                                  The info on the springs comes from Neil and if you need springs for 84mm scissors, he has them, they just aren't listed on edcsource so you'll have to PM him.

                                  1 Reply Last reply
                                  • sergemaster Offline
                                    sergemaster
                                    Posts: 1,058
                                    sergemaster Offline
                                    sergemaster
                                    wrote on last edited by
                                    #8 Quote Reply

                                      Amici,
                                      I recall when I had ro replace the spring on my 20 + year Swisschamp, I found some doc online at the time that turned out to be quite helpful for a pretty painless procedure. Picked up my springs from Rotokid a few years back plus some.

                                      Cheers,
                                      Serge

                                      1 Reply Last reply
                                      • J Mackrel Jones Offline
                                        J Mackrel Jones
                                        Posts: 731
                                        J Mackrel Jones Offline
                                        J Mackrel Jones
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Instructions from The Swiss Army Knife Owner's Manual:
                                          "Pull out the scissors (or pliers) half-way, so that the hole in the
                                          fixed arm is well clear of the body of the knife. Put the knife on its side on
                                          a table. Support the scissor-arm with something about the same thickness
                                          as the height that the scissor is off the table, like a pencil or several coins.
                                          Put this support close to, but not right under, the spring-hole, which is filled
                                          right now with the circle-end of the broken spring. Get an awl or find a nail
                                          with a tip just larger than the hole in the center of the spring-end, but
                                          smaller in diameter than the hole in the scissors. Hold its point in the center
                                          of the circular spring-end and tap the head of the nail straight down
                                          with a hammer. Light taps will do it. The support prevents bending the
                                          scissors and keeps the hammer-taps solid. And so drive the broken spring
                                          out of its hole. If you’re careful you won’t drive the end of your small pointy
                                          tool into the top of the table.
                                          The circle-end of the new spring should be just a little too big to go
                                          into the hole; it will be a press-fit. Slide the straight section near the base
                                          of the spring into the slot between the hole and the shaft of the scissor-arm
                                          and start the circle at an angle partway in the hole, starting with the opening
                                          in the circle. Hold it in this position with a pliers and squeeze as you
                                          rock the pliers and spring into line." (with photo)

                                          1 Reply Last reply
                                          • Syph007 Offline
                                            Syph007
                                            Global Moderators
                                            Posts: 9,842
                                            Syph007 Offline
                                            Syph007
                                            Global Moderators
                                            wrote on last edited by
                                            #10 Quote Reply

                                              The only tools ive used to swap spring is my vic huntsman. Awl to push out old spring, and then the side of a big tool like the bottle opener to push the new spring home with. Pliers would likely be easier though.

                                              1 Reply Last reply
                                              • demonoflust Offline
                                                demonoflust
                                                Posts: 243
                                                demonoflust Offline
                                                demonoflust
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  @enki_ck said:
                                                  The info on the springs comes from Neil and if you need springs for 84mm scissors, he has them, they just aren't listed on edcsource so you'll have to PM him.

                                                  I would love to, but will Neil ship to Singapore? Not sure if the shipping cost is going to be expensive.

                                                  1 Reply Last reply
                                                  • enki_ck Offline
                                                    enki_ck
                                                    Global Moderators
                                                    Posts: 20,936
                                                    enki_ck Offline
                                                    enki_ck
                                                    Global Moderators
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      @demonoflust said:

                                                      @enki_ck said:

                                                      The info on the springs comes from Neil and if you need springs for 84mm scissors, he has them, they just aren't listed on edcsource so you'll have to PM him.

                                                      I would love to, but will Neil ship to Singapore? Not sure if the shipping cost is going to be expensive.

                                                      His shipping is very reasonable and he ships most places. Why not send him a PM here and ask for a shipping quote.

                                                      404 Not Found

                                                      favicon

                                                      (forum.multitool.org)

                                                      1 Reply Last reply

                                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                      With your input, this post could be even better 💗

                                                      Register Login

                                                      1. Home
                                                      2. Tool Talk
                                                      3. Swiss Army Knights Forum
                                                      4. Sissors spring question
                                                      Reply
                                                      • Reply as topic
                                                      Log in to reply
                                                      COMMUNITY LINKS
                                                      EDC-TV SAKWiki GearFeed SAKSelector
                                                      Operational Funds

                                                      Help us keep the Unworkable working!

                                                      Make A Donation
                                                      November Goal: $300.00
                                                      Due Date: Nov 30
                                                      Total Receipts: $0.00
                                                      Below Goal: $300.00
                                                      0% funded
                                                      • Login

                                                      • Don't have an account? Register

                                                      • Login or register to search.
                                                      • First post
                                                        Last post
                                                      0