Skip to content
  • Categories
  • Recent
  • Popular
  • World
Skins
  • Light
  • Dark

Collapse

NodeBB

The PMP (Pimped Mini Prybar)

Scheduled Pinned Locked Moved The Mod Squad
13 Posts 1 Posters 5.9k Views
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • MetropolicityM
    MetropolicityM
    Metropolicity
    wrote on last edited by
    #1

    Taking a break from packing up our house and decided to dig into my tools one last time.

    Since we started pack, we are endlessly taping boxes with packing tape, opening boxes, repairing things taken off the wall and removing small nails and such. So, I pulled out my trusty 3" straight widgey bar from County Comm. I like the straight widgey because they are flat and do the job with a little less leverage than it's curved brothers. I would never buy one of those mega expensive Atwood tools, so time to make my own.

    A little bit of research, use analysis and some material research, I went out to the shop and stock straight widgey bar and out came this...my PMP (Pimped Mini Prybar).

    The paint is a hard wearing enamel based paint, sprayed with a 'stipple' effect (sprayed from more than 14" away with purposeful over spray). This stipple effect created texture on the paint. A couple of coats of clear sealed it in. I baked it in my toaster oven (shop one, not my kitchen one) at 200F for about 45 mins. Cured it good and solid.

    The main use for the the PMP is to cut tape and open boxes so after giving the tip a little bit of profiling to smooth out the ramp, I took a round file and roughed out a little notch that make a little pokey box/tape cutter. Then polished with a 600 grit wet paper.

    Some jimping for a little grip when cutting duct tape or harder stuff:

    I've used my pico widgey as a screw driver before but since I semi sharpened the pry bar end of the PMP, I re-profiled the round end of the back side into a big flat bit driver.

    I wanted to avoid a paracord wrap as I wanted to keep this as flat as possible, so I used some wide shrink tube for some grip. I learned a lesson from my pico widgey, so to avoid the tubing from slipping off, I stuck a small strip of skateboard grip tape underneath the tubing before shrinking. The result is a grip that has some texture but not overly overwhelming. A little lanyard made from a mini ziptie folded in half and heat shrunk the same way (grip tape etc).

    The reason why I wanted to keep it as flat as possible is that for the last week I have been carrying my BO Wave and Spacepen around the house for repairs before we move. The Skinth VS prototype I've been carrying has a TINY pocket up front no good for much else but bandaids and...you guessed it...The PMP!

    The grippy mini-lanyard makes extracting the PMP easy.

    My Skinth VS loadout: The Black Tide (Ultimate BO Wave) a Black Space Pen and the PMP.

    So that's how you can pimp your mini pry bar.

    Hack on!

    1 Reply Last reply
    0
    • AHBA
      AHBA
      AHB
      Admin Team
      wrote on last edited by
      #2

      Excellent work.. :tu:

      1 Reply Last reply
      0
      • DavidD
        DavidD
        David
        wrote on last edited by
        #3
        1. Great work on that pry bar. :tu: I got a thing for little pry bars. But have not modded one yet. 🙂
        1 Reply Last reply
        0
        • Sparky415S
          Sparky415S
          Sparky415
          wrote on last edited by
          #4

          I like that a lot :tu: and the grip tape under the heat shrink idea is genius :salute:

          1 Reply Last reply
          0
          • VladimirV
            VladimirV
            Vladimir
            wrote on last edited by
            #5

            Really excellent prybar!

            1 Reply Last reply
            0
            • R
              R
              radiotecha1234
              wrote on last edited by
              #6

              Okay, so how much for a box of twenty? Just kidding. But, that is nice work. And very handy.

              1 Reply Last reply
              0
              • tattoosteve99T
                tattoosteve99T
                tattoosteve99
                wrote on last edited by
                #7

                What kind of paint was that you used? How well will it hold up? Nice work!

                1 Reply Last reply
                0
                • MetropolicityM
                  MetropolicityM
                  Metropolicity
                  wrote on last edited by
                  #8

                  It's hard wearing high temp enamel. Sprayed on with light coats and baked on.

                  1 Reply Last reply
                  0
                  • Mike, Lord of the Spammers!M
                    Mike, Lord of the Spammers!M
                    Mike, Lord of the Spammers!
                    wrote on last edited by
                    #9

                    Certainly looks the part matey 🙂

                    1 Reply Last reply
                    0
                    • enki_ckE
                      enki_ckE
                      enki_ck
                      Global Moderators
                      wrote on last edited by
                      #10

                      @sparky415 said:
                      I like that a lot :tu: and the grip tape under the heat shrink idea is genius :salute:

                      Agree, this is an excellent idea. I love every part of it. Even the small lanyard is pure genius. :tu: I might have to steal/borrow this. 👼

                      1 Reply Last reply
                      0
                      • T
                        T
                        TheRodfather
                        wrote on last edited by
                        #11

                        @enki_ck said:
                        Agree, this is an excellent idea. I love every part of it. Even the small lanyard is pure genius. :tu: I might have to steal/borrow this. 👼

                        Ditto. Great job

                        1 Reply Last reply
                        0
                        • MetropolicityM
                          MetropolicityM
                          Metropolicity
                          wrote on last edited by
                          #12

                          I REALLY wanted to get rid of the can/bottle opener on my Black Tide in favor of a chisel or something useful, so inspired by a simliar design but in reverse, I went ahead and added a cap lifter to my PMP.

                          Using a 1/4" solid carbid end mill, I was able to get through the D9 steel pretty easily, the rest was done on a 1x30 belt sander.

                          While I was there, I resanded the tip to 1000 grit and then a quick polish on my cloth wheel with diamond paste. Mirror shiny! This gave the little hook a sharper edge.

                          Then masked the tips with tape, and reshot it with enamel paint and a coat of clear. A quick bake at 250F for 30 mins and boom, back in action!

                          It's a downward pushing motion for the opening action instead of the traditional upwards pull.

                          And with the rest of my black edc. Working out well so far!

                          Now to think about what to replace the cap lifter with on my Black Tide.

                          1 Reply Last reply
                          0
                          • MetropolicityM
                            MetropolicityM
                            Metropolicity
                            wrote on last edited by
                            #13

                            Haha. Gave it a go on some awesome Canadian beer, Steam whistle

                            1 Reply Last reply
                            0

                            Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                            Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                            With your input, this post could be even better 💗

                            Register Login

                            • Login

                            • Don't have an account? Register

                            • First post
                              Last post
                            0
                            • Categories
                            • Recent
                            • Popular
                            • World