homemade tools
-
I've only tried modding 58mm SAK's and Leathermans, but if you're looking at modding SAK's most of the sticky posts cover the basics. Ball peen hammer, files, a vice, definitely a drill (or drill press), for starters. I'm sure I'm forgetting some other stuff.
Have fun modding, and welcome to the forums! :D
-
dremel is a must

-
I don't want to scare ya but this is what I use to mod and make stuff:
As for tools....I do most of my work with 5 'basic' shop tools, I'll go from biggest to smallest. I write basic because a proper machine shop is typically comprised of these machines but larger, especially the sander. I recently bought a oscillating spindle sander but have only found one use for it so far.
1. I have a X1 Harbour Freight mini mill. This little beast can chuck up stuff with a 8" travel between ends. This combined with solid carbide end mills, aluminum and steel is no match for my modding might. I swapped out the very noisy gear system for the spindel for a belt drive, so much faster and safer if it binds. This is how I made the milled slot for the OHO blade exchanger.

Can be found here: Harbor Freight Mini Mill
2. Matching the X1 is a 7x 10 mini lathe, capabile of chucking up stuff 3" in diameter. Again, carbide tools and some tuning, it can get pretty damn tight for tolerances.

Can be found here: Harbor Freight Mini Lathe
http://www.harborfreight.com/7-inch-x-10-inch-precision-mini-lathe-93212.html
**3. For majority of my grinding needs, I use a 1x30 and 5" combo sander. The belt is the perfect size for grinding small parts and the 5" disc takes off lots of material in a short amount of time. I like the 1" becuase I can use the none backed portion for sanding tight curves and getting into open slots like the bottle opener of the PMP. I use a Mastercraft one, but it's pretty close this one at Harbor Freight:
**

1" Belt and 5" Disc combo sander
http://www.harborfreight.com/1-inch-belt-and-5-inch-disc-combination-sander-34951.html
4. The venerable Dremel tool is just about the hardest working tool I have. I own 4 and they all are set up to do different things. One is on a stand with an extension, one is mounted on a table upside down like a mini spindle sander, one regular one and one with a 90 degree adaptor. I pick up cheap ones every once and while and find ways to set them up differently.

5. The last tool...is technicaly a series of tools. Files and sandpaper....lots of them.
As much as a Dremel is a great tool, nothing beats a hand file for control. Various round files, mini round files, flat ones, triangle...I buy as many as I can because I break them all the time. Sandpaper is one of the most important tools because it makes even the craziest hack into the most professional mod. Everything from 100-1500...wet and dry.
I can go into the whole "not all files are made the same", but I haven't met a file I didn't like. Typically I get some of those micro ones that come in a set of 8-9 at hardware stores, they have a bunch of profiles that are small enough for grinding, but big enough to make work. I use the 1/8 round one a lot and the triangular one I space out jimping properly. Most discount hardware stores have sets made in china for less than $10, get two because it sucks to be 3/4 through a project and loose the right file profile.
Needle Files:
Husky Set at Home Depot
http://www.homedepot.ca/product/6-piece-needle-file-set/974512

If you can, get the same set in diamond file for finishing.
Diamond Needle Files Amazon
http://www.amazon.com/SE-Diamond-Needle-Files-3-25/dp/B000SQOKR0

The little box cutter notch is done with a 1/8" round file. The bottle opener is a bit tougher, solid carbide 1/4" bit to get through the hole and then my 1"x30" to remove the rest of the material. The jimping (hard to see but its on top) was started with the triangle file and then rounded out with the 1/8" file.
Similar jimping with the 1/8" round file:
and some more jimping on the blade exchanger
A medium 12" one will also be useful. Look for fine to medium teeth, any bigger and it'll just skip across steel and not remove material.
Make sure you get a file card, files get clogged, these get them cuttin' again:

Of course, sandpaper. I usually start with 150 after filing, then 220 wet for a brush finish and 600-1200 for finer, more accurate finish is parts need to mate or rub.
If you have a drill press, and everyone should, get a small cotton wheel or cone and some white diamond stick compound, green compound or rouge, thatll get steel nice and shiny. I turned mine on it's side and it worked great, if you have the space.

That's pretty much it, go slow and check often. Files won't let you know you've gone too far.
So it's a pretty 'basic' machine shop but the two most important tools for any modding den is definitely a Dremel tool, files [/img]and sandpaper.
-
Second hand is the way to go for hand tools you can pick up hammers, vices etc etc very cheaply

Where in the world are you?
If you are in the UK car boot sales are great
Or in the USA try Garage salesGood luck

-
@ Metropolicity setup!
I wish I had the space for all that. -
All I'm rocking at the momemt is a drill press, orbital hand sander, 2 dremels and a huge pile of files and sandpaper. I'm saving for a mill though. :D
You can work alot of magic with files and sandpaper, but to drill straight accurate holes you really need a drill press.
-
Files, lots of files :D
A drill press should be first on the list of power tools.
I want a mill!
And a lathe... and a .... .... (insert long list here).
-
@Zag said:
@ Metropolicity setup!
I wish I had the space for all that.oh man..I should of taken a pic of my old shop before I tore it apart for shipment to the new house.
The NEW shop...mmm..think a wall of acrobins for storing random small parts, a BIG long butcher block bench with the mill, lathe and other heavy machinery, a smaller cork lined assembly table and epoxy painted floor!
I can't wait.
But yah..back to the issue at hand, Drill press, Dremel, Diamond bur set, a vice or clamps, files, sand paper...get it now and get it fast.
-
Just a question, what would you use the diamond burr bits for? Enlarging holes? Just curious
-
@clickstop said:
Just a question, what would you use the diamond burr bits for? Enlarging holes? Just curiousThey do the same as files, removes material but just at a much slower rate that steel files and leaves a decent finish. The diamond burrs are usually some where between 100-200 grit.
-
Aaah...good stuff! I'll have to get some for my dremel..
-
:o holy , dang. metropolicity....u have all the trick toys. thnx for the replys everyone. i've got alot of reading.
-
Believe it or not I'm working on building a riveting machine.
-
@tattoosteve99 said:
Believe it or not I'm working on building a riveting machine.SWEEEET!
I have a manual press that I can use for rivets for fabric, but I think they'll work for metal. Hard to say.
All I have is a pop rivet gun from the late 80's :)
-
Think automatic. More info later.
-
Hi'
Would to share my idea , My Home made router base JIG for inlay work .
;)
-
I love the DIY router table! I actually picked up another dremel to do something similar for edge round overs. Nice work!
-
-
Nice to see you here Taninaree
I have not seen you posting for a while
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login