Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Question

Scheduled Pinned Locked Moved General Tool Discussion
16 Posts 1 Posters 2.3k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Question
Question
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • bushidomosquito Offline
    bushidomosquito
    Posts: 660
    bushidomosquito Offline
    bushidomosquito
    wrote on last edited by
    #4 Quote Reply

      What finish? It's bead blasted stainless.

      1 Reply Last reply
      • mkianni Offline
        mkianni
        Posts: 78
        mkianni Offline
        mkianni
        wrote on last edited by mkianni
        #5 Quote Reply

          Here's the before pics, although I really don't think you can see much.

          Acetone was actually going to be my first choice, but I was going to wait and see if anyone has experienced this exact same problem before I try anything.

          I actually had to use another tool just to open it as far as I did for the pic. :o

          I should also clarify my earlier statement....it's hard as a rock in some places, and kinda sticky/gummy in others. Different stages of deterioration I guess.

          001.JPG

          002.JPG

          003.JPG

          1 Reply Last reply
          • Sparky415 Offline
            Sparky415
            Posts: 13,000
            Sparky415 Offline
            Sparky415
            wrote on last edited by
            #6 Quote Reply

              I don't know what else you have laying around your house but meths or white spirit will also work, looks like it will need a soak :tu:

              or

              ( Dishwasher when the missis isn't looking (if there's no plastic) then a drop of oil ;) )

              1 Reply Last reply
              • Chako Offline
                Chako
                Posts: 22,725
                Chako Offline
                Chako
                wrote on last edited by
                #7 Quote Reply

                  My advice, get yourself one of those jewelry ultrasonic cleaners. I have a cheap on and it does a good job cleaning MTs and knives with soapy water. I run it through several cycles and get in there with small brushes and Q-Tips. You could use something else other than water in the stainless tub. The cleaning action does a great job losening dirt in hard to reach areas.

                  1 Reply Last reply
                  • bushidomosquito Offline
                    bushidomosquito
                    Posts: 660
                    bushidomosquito Offline
                    bushidomosquito
                    wrote on last edited by
                    #8 Quote Reply

                      Your first choice was correct. Acetone will get in there and completely dissolve any remnant of that goop out of every crevice no matter how crustified it is. Then it will be just bare stainless with no residue and you can lube it with something nice like Rem-Oil or CLP.

                      1 Reply Last reply
                      • Doraemon Offline
                        Doraemon
                        Posts: 92
                        Doraemon Offline
                        Doraemon
                        wrote on last edited by
                        #9 Quote Reply

                          Acetone works well. I get this in some of my NOS Leatherman tools and usually use a cotton bud or brush to clean it. I've never tried soaking it though. Those that I encounter did not really gummed up the joints or affect the functionality of the tools. It's ok to leave it as it is.

                          1 Reply Last reply
                          • parnass Offline
                            parnass
                            Posts: 1,653
                            parnass Offline
                            parnass
                            wrote on last edited by
                            #10 Quote Reply

                              @mkianni said:
                              I have several shrade tools that I purchased some years ago and never used. I opened one up today to find the original factory grease has turned to a hard, semi sticky substance that has gummed up the tools movement and normal operation. ...

                              I bought a couple of those USA-made Schrade multitools several years ago and the implements were really difficult to open no matter how much I used them. This won't answer your question, but you might never get them to open easily. :(

                              1 Reply Last reply
                              • Biru Offline
                                Biru
                                Posts: 618
                                Biru Offline
                                Biru
                                wrote on last edited by
                                #11 Quote Reply

                                  I've cleaned my multis with WD-40 and a stiff toothbrush and have never had a problem. I have an American Schrade and WD has not harmed it. I've used WD on dozens of items and never had it damage anything.

                                  I have a 60's Colt Detective Special which was a concealed carry gun that never saw much use. The lubrication in the cylinder had set up over time and locked up the cylinder. I shot WD into it and let it soak a bit. It took maybe two washes and now the cylinder spins cleanly. The only drawback was that the first shot of oil to lube the cylinder was thinned by the remnants of the WD. I re-oiled it and now it's like new.

                                  I don't know if this helps, but I hope it does. Good luck.

                                  1 Reply Last reply
                                  • mkianni Offline
                                    mkianni
                                    Posts: 78
                                    mkianni Offline
                                    mkianni
                                    wrote on last edited by
                                    #12 Quote Reply

                                      I'll give the WD a try today. I didn't think about WD, that is some pretty strong stuff. From my experience with it on past projects, I'm sure it'll work just fine. If not, acetone it is.

                                      My brother, retired co. sheriff, has one of those colt detective specials. I fired it a few times at the range. Nice little gun, and surprisingly accurate too! :tu:

                                      Thanks again for the advice, everyone, and enjoy your Sunday. I'm off to find some treasures at the yard sales before the heat wave sets in! :cheers:

                                      1 Reply Last reply
                                      • Biru Offline
                                        Biru
                                        Posts: 618
                                        Biru Offline
                                        Biru
                                        wrote on last edited by
                                        #13 Quote Reply

                                          Good luck! :) As I say, I don't think there's a multitool with a finish anywhere near as sensitive to solvents as old Colt bluing- and WD did not harm my old Colts in any way. I've used it on fishing reels, guitars and amplifiers and power tools and have never had it do anything but an excellent job. It might take a soak or two to get all the gunk out.

                                          1 Reply Last reply
                                          • Carlos Offline
                                            Carlos
                                            Posts: 562
                                            Carlos Offline
                                            Carlos
                                            wrote on last edited by
                                            #14 Quote Reply

                                              wd40 contains good and non aggressive solvents, for sure. One other product I personally haven't yet tried but heard so many marvelous for these kind of things is googone -- http://googone.com/

                                              1 Reply Last reply
                                              • mkianni Offline
                                                mkianni
                                                Posts: 78
                                                mkianni Offline
                                                mkianni
                                                wrote on last edited by
                                                #15 Quote Reply

                                                  The WD40 worked fine. I didn't even have to soak it, the hard grease broke right up with just a little effort from an old tooth brush.

                                                  Thanks again everyone! Can't believe I forgot about WD! ???

                                                  1 Reply Last reply

                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                  With your input, this post could be even better 💗

                                                  Register Login

                                                  1. Home
                                                  2. Tool Talk
                                                  3. General Tool Discussion
                                                  4. Question
                                                  Reply
                                                  • Reply as topic
                                                  Log in to reply
                                                  COMMUNITY LINKS
                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                  Operational Funds

                                                  Help us keep the Unworkable working!

                                                  Make A Donation
                                                  November Goal: $300.00
                                                  Due Date: Nov 30
                                                  Total Receipts: $0.00
                                                  Below Goal: $300.00
                                                  0% funded
                                                  • Login

                                                  • Don't have an account? Register

                                                  • Login or register to search.
                                                  • First post
                                                    Last post
                                                  0