Mr. Pinchy mods
-
I have an old, first generation (I think) Multi-Plier in black oxide that was my first ever and still favorite multitool. Years ago the tools started getting loose, and (this is before I knew about locktite) I got sick of tightening them daily with a hex wrench, so I retired it and bought the then new, shiny MP400, which I've carried for years and never liked.
Recently, I found the old one in the glove compartment, and realized that what I really wanted is to bring it back to life again.
A bit of teflon tape solved the loosening bolts problem just fine, but I realized/remembered that there were other problems with this tool (pinching being one of the unavoidable ones). Of course, these problems are similar for most of the multitools I've looked at
I work on computers a lot, and frequently find myself needing to go back to the office and grab a screwdriver, because the one on my multitool is too short to fit into the deep holes you find on monitors (the biggest offenders are the screws holding on the stand) and other equipment.
So here is my thinking. Leatherman has those neat flat screwdriver bits, and with their MUT they introduced a longer version that might just work: http://www.leatherman.com/accessories/product/MUT_Bit_Kit
I'm pretty sure that's no thicker than the file on my MP, so I've started thinking about looking for a metalworking shop that could take something the thickness of that file and make instead a tool-steep flattened Phillips-head screwdriver in its place.
At the same time I figured I'd look for a first generation non-black one with scissors and replace the knife blade with them, as I carry a much better knife all of the time, but could really use a set of scissors, even if I have to use some cold blue to get them to somewhat match the rest of the tool.
I know very little about steels and less about metalworking, though enough to assume that nothing in my home shop is likely to cut steel hard enough to make a reasonable screwdriver this way. I'm also assuming that breaking off the pieces from another tool and welding onto the backpiece wouldn't work, even if I had the equipment. So this may very well be a nonstarter for me, unless there is a metalworker who could machine the part I need for less than the cost of a tool that already HAS the parts I need (MUT is $100 or so).
So... Now that I've had an idea and shot it down myself, I'm wondering if anyone out there had actually done something like this?
-
Welcome Tp1l

You could try posting this in 'The Mod Squad'
There's some clever 'metal headed' guys there that might not spot this thread
They can point you in the right direction for getting some work done
-
Oh. Yeah! I'm very new to this forum and completely missed that one.
I wonder if I can move the topic, or if that's a mod(erator) job.
Thanks
Tom
-
All the proper metal working guys must be busy
so have you thought of adding SOG components?
I don't know if they will fit
or be long enough for what you need hopefully someone will be along with some more advice -
@sparky415 said:
All the proper metal working guys must be busyso have you thought of adding SOG components?
I don't know if they will fit
or be long enough for what you need hopefully someone will be along with some more adviceIt´s a bit off topic, but has anybody ever tried to incorporate SOG components into a Gerber of any kind? (I think the OP wants to know about teh original Multiplier, but I´m thinking about modding my MP 600)
side by side pics would be great.Or if anybody would care to do a pic of a SOG component and measure it and tell us teh dimensions?
-
I had looked at SOG components briefly once I realized that they had some for sale separately, but haven't seen them in person to do any kind of comparison. That Phillips head may be too short for my purposes, but it's a lot closer than that I have now.
I pulled the file off my Gerber (yes, this is a non-locking older model) and took a photo, then dropped in the Leatherman MUT bit as close to correctly scaled as I could get (it's a 1/4" bit I think). The SOG piece is simply eyeballed, and that's assuming it is about the same overall height as the Gerber piece.

Sorry about the photo quality. Crappy iPhone camera and bad office lighting worked against me in that regard. I won't really know until and unless I buy one and just try it out, but it doesn't look promising. Though I do wonder if a Leatherman bit holder could be modified to fit into my Gerber. I don't own any new Leathermen (if I had the money for one, I wouldn't be concerned with this mod honestly) and I haven't seen any photos of the bit holder alone that I could scale and match up to this.
Is there an archive of photos anywhere of bits from various tools in scale with each other? If not, that might be something worth creating at some point just to answer this kind of question.
Tom
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
