The Improviser 1.0
-
Heya Fellas,
I will say now, that this is all Metro/Erics fault. ;) This has been about a month in the making, after seeing all of metros mods posted over at EDCF. This started as a Pliers swap, ST300 into a Surge. Simple.
Then I go to thinking about the other tools I use... This now involves two Surge, one regular, and one black oxide, and a ST300 for parts, all brand new and un-used(other than my testing different loadings of tools), mixed and matched. Oh, and the larger hideaway lanyard loop from my Wave.
Lots of different tool loading in the past few weeks, but I think I have finally found the tool load out that I like (and that can actually be put together).
Called the Improviser, since that's basically what I'm doing if I need it; out and about improvising, and scrounging/scavenging parts and supplies, to make something work. I do a LOT of Mcguyvering things to get by.
So, I made a quick list of the tools I use the most on my multis, in order of importance based on frequency...
Pliers
Phillips driver
flat driver-- as a pry tool.
Awl/pick
file
Wire cutter
scissors
saw
Knife Blade; I never use the knife on a multi, since I carry a dedicated knife for cutting.
I'm trying to get rid of both knife blades on this tool if I can.I wanted the fixed phillips driver, both for reach, and it is full profile, should slip less than the flat bits. I'd really liked the similar driver on my Spirit, just not that it was so smooth, and slipped, plus hard to open. So I knew on the LM, that I wanted it, a great improvement being the LM one has a tab for opening it, even if it is inside the tool as opposed to the Vic.
Based on that, I wanted a fixed flat driver too. Also a flat driver can double as a scraper and light pry tool. Bit driver still included though for other fastener types, and other sizes of phillips and flat. Awl for picking prying and scrapping. Can opener because every time I stop carrying a tool with one, I need one...
Now, as to the file and saw... I use both regularly, but the file a lot more.
I'm lazy. Its too much hassle to carry the saw around loose and have to change the blade in the holder every time I need it.
So, dual blade changers needed.Which, rids me of the useless (IMO) serrated blade.
Went with the ST300 pliers for the changeable cutters, I tend to mangle and notch wire cutters while cutting non wire items...
Took several variations over the past couple weeks to get down to what I wanted, and needed, and to make it all stack and fit right.... I had this same tool loading in there 3 ways before I figured the right one so the pliers cleared everything right, and the tool would close all the way. Several threads here were invaluable for showing what had to be ground and cut out of the handles, and also some great advice directly from Metro.
Mixed the BO parts in for fun, and color contrast.
I'm planning to have the handles cerakoted red or orange, not sure yet which. I also might add one hand open holes to the blade changers, but I'm not sure I'll really need that.
Thinking of doing away with the plain edeged blade, in favor of another blade holder, and then I can get a t-shank metal saw, or even a knife edge t-shank blade and have a replaceable utility blade. But I don't want to buy another whole surge to get the blade holder, so thats a back burner idea.


G.
-
Great job Ice Tigre

-
I really like this tool setup, best of both worlds. Long drivers and bit adapter.

-
Awesome job man!!!

It is looking really awesome, and I love the tool set up. Please keep us updated!!
p.s. I would love to see it red cerakoted
-
that is a sweet looking mod... nice assortment of tools that you ended up going with. I really like swapping the serrated blade out for another blade holder, and the contrast of the SS and BO parts is a nice touch!

I think a nice, deep green cerakote would look awesome, but red works too. ;)
-
Wow, awesome work dude. Your point on ditching both blades on the MT when you have another blade on you is something I hadn't considered before. I smell another mod in my future, lol.
Also, curse you and Metro, now I need to go find a BO wave (and probably rebar):P I think I'll start with the two-tone look like you have though, that looks slick.
-
@Delta10 said:
Wow, awesome work dude. Your point on ditching both blades on the MT when you have another blade on you is something I hadn't considered before. I smell another mod in my future, lol.Also, curse you and Metro, now I need to go find a BO wave (and probably rebar):P I think I'll start with the two-tone look like you have though, that looks slick.
Just wait till to get on the cerakote train. It's a really really fast moving train and your can't tuck and roll.
-
Thanks All!
Its great fun working on these, and slightly addicting too, I've found....
So, if I can't find another blade changer for this, I'm looking at the "disassembly pin" holder from the MUT, to replace the blade. Just hope the pivot size is the same. Otherwise, I guess it'll have to be a knife blade for a while.One hope I had for making it knife blade free, is then it should be TSA and flight friendly!
G.
-
Its great fun working on these, and slightly addicting too, I've found....
So, if I can't find another blade changer for this, I'm looking at the "disassembly pin" holder from the MUT, to replace the blade. Just hope the pivot size is the same. Otherwise, I guess it'll have to be a knife blade for a while.One hope I had for making it knife blade free, is then it should be TSA and flight friendly!
G.
The pivot is the same size. :)
-
Its great fun working on these, and slightly addicting too, I've found....
So, if I can't find another blade changer for this, I'm looking at the "disassembly pin" holder from the MUT, to replace the blade. Just hope the pivot size is the same. Otherwise, I guess it'll have to be a knife blade for a while.One hope I had for making it knife blade free, is then it should be TSA and flight friendly!
G.
sad to say, but I doubt you'll have much luck getting past TSA with a saw on there. :-\
-
Thanks All!
Its great fun working on these, and slightly addicting too, I've found....
So, if I can't find another blade changer for this, I'm looking at the "disassembly pin" holder from the MUT, to replace the blade. Just hope the pivot size is the same. Otherwise, I guess it'll have to be a knife blade for a while.One hope I had for making it knife blade free, is then it should be TSA and flight friendly!
G.
sad to say, but I doubt you'll have much luck getting past TSA with a saw on there. :-\
Or can opener or awl...
-
Hrrmm. I was under the impression that the knife-less fuse that I used to read as being reported as getting through airports, had a saw on it... or the awl at least... Hmm. My memory is going it seems.
Aw well, no matter, it was a side thought for my Europe trip in 2014...
Thanks Metro!
Now, all I gotta do is get one... And decide if it reeeaaally could use anything I could thread onto it, enough to justify having it on here.Anyone have any other suggestions; what to put on instead of the knife blade?
G.
-
@Ice Tigre said:
Hrrmm. I was under the impression that the knife-less fuse that I used to read as being reported as getting through airports, had a saw on it... or the awl at least... Hmm. My memory is going it seems.Aw well, no matter, it was a side thought for my Europe trip in 2014...
Thanks Metro!
Now, all I gotta do is get one... And decide if it reeeaaally could use anything I could thread onto it, enough to justify having it on here.Anyone have any other suggestions; what to put on instead of the knife blade?
G.
Well European TSA tends to be even heavier handed; I've read them confiscating even screwdrivers. :/
-
@Sazabi said:
Well European TSA tends to be even heavier handed; I've read them confiscating even screwdrivers. :/The law says so. But some officials might let go. For the record, each EU country member must follow THIS: http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=CELEX:32010R0185:EN:HTML
If you open that link and jump to ATTACHMENT 4-C you'll see the complete list of forbidden articles, which includes the screwdrivers.
This is pretty similar to the constraints to go to the football or concertos, that kind of stuff.
-
The pivot is right but it's WAY too thick for the Surge pivot, it's nearly 3/16" if I remember.
-
Hmm. Well, I guess I could mill it down thinner, but thats a lot of work on top of buying a MUT just to steal parts... To steal one part. Looks like its down to the blade holder, unless I can think of something else to put on it.
G.
-
A truely usefull MT
great job 
-
Well, I decided a dental pick mounted on the tool would be nice, instead of carrying it seperately...
((Warning, EXTREME Modding follows! ;) )) So, I decided i could either make a pick, mod a pick onto a new tang, or mod a pick and a existing blade tang to hold it... I went with the last option, since I was never good at fitting liner locks from scratch, and I'll never use the serrated blade anyway. And chopping an existing pick is just plain easier han making one. Also, its an excuse to play with my welder.

Pick and useless serrated blade;

laid out for length and spacing;

Cut, noched, andfit;

Welded, ground, and polished;


not my best welds, but small parts and dis-similar metals make it harder. Not pretty, but solid.
Mounted;


Success!
G.
-
Niiiiiice. Better reach beats my dental pick mod :)
I'll have to give this a go on a mod someday.
-
The tooth ache's nightmare
:ahhh :ahhh. If I ever go to a dentist & they pull out Leatherman mod like that I am running :o :D :D.Nice work mate 8) 8)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login