Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

SAK Jig

Scheduled Pinned Locked Moved Swiss Army Knights Forum
5 Posts 1 Posters 2.3k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. SAK Jig
SAK Jig
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • WoodMan Offline
    WoodMan
    Posts: 181
    WoodMan Offline
    WoodMan
    wrote on last edited by WoodMan
    Quote Reply

      I wanted to share a SAK jig that I've found useful. I use it to confirm positioning/operation of components. It doesn't help with actual assembly.

      The first image shows the opener layer installed on the jig. The rods are cut from a wire coat hanger, but any slightly undersized metal wire will work, of course.

      The second image shows the blade layer on the jig. The large blade on this knife was savagely sharpened by a previous owner and will be replaced.

      The third image shows an 84mm combo tool installed in place of the small blade. Due to encouragement in another thread, I acquired and disassembled a cellidor Bantam to obtain the combo tool. The jig confirms that the 84mm combo tool works perfectly on the 91mm knife in direct replacement of the small blade and the only modification required is the redrilling of the hole in the combo tool.

      The fourth image shows the blade layer tools in the deployed position. The wooden blank on top allows even pressure/clamping to be applied to the assembled knife to confirm correct operation.

      IMG_0529 800x533.jpg

      IMG_0530 800x533.jpg

      IMG_0531 800x533.jpg

      IMG_0532 800x533.jpg

      1 Reply Last reply
      • crackout Offline
        crackout
        Posts: 864
        crackout Offline
        crackout
        wrote on last edited by
        #1 Quote Reply

          @WoodMan said:
          The rods are cut from a wire coat hanger, but any slightly undersized metal wire will work, of course.

          Doesn't look so slightly to me. ;)
          I found that non-matching pivot holes and pinstock result in a lot of snap-loss, which would influence your testing results, especially when working with reshaped tools and springs.

          1 Reply Last reply
          • Syph007 Offline
            Syph007
            Global Moderators
            Posts: 9,842
            Syph007 Offline
            Syph007
            Global Moderators
            wrote on last edited by
            #2 Quote Reply

              I do something kind of similar. I use aluminum blocks and sink brass rods in them to use as test fit up blocks for each size and type of SAK I work on. It makes things easier than trying to use individual pins for sure.

              1 Reply Last reply
              • WoodMan Offline
                WoodMan
                Posts: 181
                WoodMan Offline
                WoodMan
                wrote on last edited by
                #3 Quote Reply

                  @crackout said:

                  @WoodMan said:

                  The rods are cut from a wire coat hanger, but any slightly undersized metal wire will work, of course.

                  Doesn't look so slightly to me. ;)
                  I found that non-matching pivot holes and pinstock result in a lot of snap-loss, which would influence your testing results, especially when working with reshaped tools and springs.

                  I measure .071"/1.81mm for the wire coat hanger stock that I used. This undersizing allows for easy assembly of parts on the jig. It also allowed me to check the fit of the 84mm tool on the 91mm frame since the diameter is smaller than both the 2.5mm and 2.2mm standards.

                  I get snap on pretty much all the tools I've checked so far although in a few cases, the backsprings were obviously shot. Replacement with a newer backspring took care of the problem. Identification of worn out backsprings is another advantage of this jig that I neglected to mention.

                  1 Reply Last reply
                  • Sidhartha Offline
                    Sidhartha
                    Posts: 807
                    Sidhartha Offline
                    Sidhartha
                    wrote on last edited by
                    #4 Quote Reply

                      i use the same idea for assebly :tu: holding everypart in your hand trying to get the knife together is a real nightmare

                      1 Reply Last reply

                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                      With your input, this post could be even better 💗

                      Register Login

                      1. Home
                      2. Tool Talk
                      3. Swiss Army Knights Forum
                      4. SAK Jig
                      Reply
                      • Reply as topic
                      Log in to reply
                      COMMUNITY LINKS
                      EDC-TV SAKWiki GearFeed SAKSelector
                      Operational Funds

                      Help us keep the Unworkable working!

                      Make A Donation
                      November Goal: $300.00
                      Due Date: Nov 30
                      Total Receipts: $0.00
                      Below Goal: $300.00
                      0% funded
                      • Login

                      • Don't have an account? Register

                      • Login or register to search.
                      • First post
                        Last post
                      0