New Wave is this normal?
-
No. That is not normal. Usually the OHO blades are quite smooth.
-
The pliers got scuffed on my wave and the charge, adds character :D
-
Welcome to the forum and great choice with the Wave. You might apply a bit of oil and see if that helps.
-
On my BO wave the finish has been taken off to bare metal on a portion of the plier head and the screws holding the outside tools in will turn slightly if you hold both sides and rotate the tool. I have found that this can affect how well the outside tools deploy, id say oil it and open/ close the stiff tools to work the oil in.

-
I sprayed it with some ballistol which didn't help. Ill try something heavier. I may pick up a couple T10H bits and loosen it up slightly.
-
@Yak-er said:
I sprayed it with some ballistol which didn't help. Ill try something heavier. I may pick up a couple T10H bits and loosen it up slightly.If you haven't done it before it is worth reading up on how to adjust LM tools (look in the MODs sub-forum). IIRC you need to heat up the screw to loosen the loctite, plus you need to move the screw, not the pin (which isn't supposed to rotate).
-
you'll need security T9's
-
Mine has scuffed the pliers, and the blade was way stiff, so i loosened it and a little oil, it works fine.
-
you'll need security T9's
Thought waves were T10H.
Yes, they are. You'll need two for the pliers end. And you might want to heat up the screws a bit to loosen the locktite. But as you bought your tool at a brick and mortar store, I'd go and return it and ask for another (good) one.
-
I have had some that slightly scuffed the pliers. As for the blade, it will most likely loosen up with use.
-
I have some with scuffing on the plier head, didnt bothered me much. You can use sand paper to even out the scratches 250 - 800 grit. As for the stiffness, its pretty common to leathermans I bought.. theyre usually a pain to open or close out of the box, especially my black oxides.
i bought 2 Black Oxide waves from different vendors from ebay and both are very very difficult to deploy. I soaked them in multi-tool oil, opened and closed a bit then left it for 2 days.
Just wondering how Victorinox Swisstools comes out of the box silky smooth to open and close.
-
Mine scuffs a little


-
All the wave/charge models I have had scuffed the pliers. My BO model is the worst. As far as the knife, sometimes they come a little stiff from the factory. I loosened the pivots on mine a Tad and it did the trick. That and some 3 in 1 oil and you will be set!!
Sent from a Galaxy S3 far, far away using R2D2.
-
Thanks for the input guys. I just wanted to make sure I didn't get a "worse than normal" tool. Seems to be well made overall, pretty happy with it. I am sure the blade will loosen up over time. I just noticed the rescue blade is nearly perfect but the plain edge is much stiffer. Thanks for your time.
-
@Yak-er said:
Thanks for the input guys. I just wanted to make sure I didn't get a "worse than normal" tool. Seems to be well made overall, pretty happy with it. I am sure the blade will loosen up over time. I just noticed the rescue blade is nearly perfect but the plain edge is much stiffer. Thanks for your time.My serrated blade is really stiff while my PE blade is the normal one. Either way, this tool goes on my belt every day and will until I break it or something really fancy comes along that I can afford. Neither are very likely scenarios.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
