Adding bones to a vic
-
I'ad like to make myself a pair of scales in giraffe bone, or may be fossil ivory, for one of my saks. I have never done it before but I have some manual ability and the right tools too (I use to work on bikes and motorbikes). Having avidly read most topics on the argoument it seems me that there are two main choises. Replicating the inlyed system of the original grips, with the factory rivet and the shims incapsulated in the interior side of the bone, or changing the blade's and the spring's rivets, discard the shim, and hammer the new wire (2 and 2,5 mm?) from the exterior before polshing the whole handle. Obviously this second way is more difficoult nd I have also read that often the knife dooes not resoult perfectly tight as from factory. Nevertheles the well polished, riveted, handles are way more appealing to me. Does any one have suggestion?
The perfect mod being changing the rivets with torx's screws or similar but it doesn not seems possible to find right diameters axles. -
I think the first thing everyone always says is, first try it on some cheap 'mod-fodders', old knives with which it's not too bad if it goes wrong. This is mainly a thing if you go try peening the pivots yourself.
I do think your torx screw idea wouldn't be too nice in a bone-scaled knife, personally I'd prefer the normal brass pins. (It does work very well with Alox, as you've probably seen in Syph007's work)
I believe PTRSAK has quite some experience with wood and bone scales.
-
Hi Bmot, you are right, peening pivots would make some marks on scales. May be not too bad if then everithing got polished with a fine compound. Small screws, even better vintage looking for flat scredrivers, can be set in the thikness of the scales. But is hard to find the right size. I am looking io motherboard pc hardwar or in eyglass stuff. Thanks for telling me about ptrsak member. Lot of fine pics in his posts.
hope he will read :) -
About the screws, Syhph007 uses torx-screws in his alox mods, (I think 2,5mm or something?) but he drills out the holes in the tools and liners before using them. I'm sure he'll be able to tell you more about it ;)
Edit: And it might not be bad to try making a post in the mod-squad forum, too (if you didn't do so already, I'm a bit behind on my forum reading...) as that's where our mods reside a lot, maybe they'll find your thread easier, to respond to it ;)
-
Hi, and welcome to the forum.
I started with making scales that clip onto the bushings, the same way original Victorinox scales do. If you are careful with the hole sizing and placement you don't need to use any glue to hold them on.
I do use a little thin Cyano' (super glue) to reinforce the holes in wood scales, but let it dry before fitting them to the knife.I have made this type of scales from wood, bone and plastic. The main thing i find is to make the holes only a tiny bit smaller than the bushing or you run the risk of splitting or cracking the scales you have just put so much hard work into.
Wenger scales are harder to make as they wrap around the outer liners which are smaller than the inner ones.
Lately I have been disassembling the knives and rebuilding them on new brass pin stock. I like the retro look of exposed pins.
The only problem with this is that the small pin is 2.2mm and that size is hard to find.
I cut the pins at least 50mm long sharpen one end and peen the other in the chuck of a drill.
This gets a nice even round head which you can polish in the drill to use on the "front" side of the knife.For most of my wooden scales I slightly countersink the holes and then sand off the protruding part of the pin after assembly.
I use an old liner as a guage to cut the pins to length, this leaves plenty of length for peening. Drill out the hole in the other end to about 8 to 10mm and it can be used to protect the scales while peening.
I use a 2oz ball-peen hammer. It is plenty heavy enough and gives you lots of control. No need for a 16oz engineers hammer here. Mine was about $6 on eBay
Slip a piece of 5 thou' (0.005") shim or a feeler guage between the layers while peening and when you pull it out your knife will have free moving blades but won't be sloppy.
As bmot said, buy a few old knives of eBay or somewhere and practice on them first.
Hope this has been a help.
My latest is this 84mm Bamtam with beef bone scales that have been "Jigged and Flamed".
Just groove the surface with a ball-end burr in a Dremel, burn the surface with a small butane torch and then scrub the charred surface with a stainless steel wire brush. I use a BBQ cleaning brush.
The end result has a nice smooth surface with a quite interesting grain effect to it and it feels so much nicer than plastic. -
Hi, PTRSAK, many thanks, lot of info in your's post. I yet bough some cheap saks from a charity sale (10-12 usd each) so I am not afraid to ruine one of my preferred. There is only a passage in Your's wonderfull post I don't fully undesrtand cause my poor english. Is this "I use an old liner as a guage to cut the pins to length, this leaves plenty of length for peening. Drill out the hole in the other end to about 8 to 10mm and it can be used to protect the scales while peening" Can you be so kind to tell me more? I had figured something similar to some of your's explanation but practise is a whole differrent thing. And the "chunk of a drill" trick is a real jewell.
Ps I have also spent one hour's at least on Your's photo album. Plenty of wonderfull pieces, and very nice bikes too :)
ps peening perfect as factory in your's jijjed bone sak
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
