De-rusting a Rebar
-
0000 steel wool always works for me. I get surface rust on my wave and it takes it right off.
-
Copy and Pasted directly from Leatherman's website:
Rust and Corrosion
All Leatherman products are manufactured from 100% high-grade stainless steel. (Exception: Screw bits for the tool adapter are made of tool steel.) But stainless steel is not rust proof; it is corrosion resistant. Depending on the mix of metal alloys, stainless steels may be highly corrosion resistant and relatively soft (like kitchen flatware), or they may be somewhat corrosion resistant and quite hard. Our products are fabricated from the latter type, so your tool components are strong and the knives retain a sharp cutting edge. Consequently, corrosion can occur in the absence of proper maintenance. Your Leatherman product should be cleaned, dried and re-oiled periodically to inhibit rust and corrosion. This is especially true if you use it in a damp or marine environment. After cleaning, re-oil pivoting areas with a light machine or penetrating type oil (such as WD-40). Buff stained surfaces with a polishing cloth or non-metallic abrasive (e.g., Scotchbrite pad or soft bristle brush).
Cleaning Methods
Depending on what your Leatherman has been exposed to, there are several cleaning methods to consider.
If your Leatherman has been exposed to salt water or marine environments, it should be thoroughly rinsed in fresh water, dried, and lubricated with a water-displacing product. If stains or rust spots appear, refer to the Rust and Corrosion section above for removal tips. If debris or sticky substances have accumulated between the blades, your Leatherman may also be cleaned in a mild solution of detergent and water. To remove tar and similar substances, clean your Leatherman with turpentine or other mineral spirits. Do not use chlorine products. After cleaning, dry your Leatherman and apply a light machine oil or a water-displacing product (WD-40®) to force out moisture trapped in the joints. This also helps protect the tool from further corrosion and sticking. -
The WD-40 might be good for rust removal, but might not be a good solution for rust prevention.
I used to have a LM Charge which I cleaned with WD40 and put aside(in a dry-weather closet). But after a year or so, the whole thing was rusted that it took me a good few hours to get it clean again. Afterwards, I used Tuf-Glide for rust prevention, and it was doing fine from that point on.
-
WD-40 should do the trick, I believe, or I'll find out soon enough. I won't have it aside for a year, though, so I'll probably spray it a bit more often, too.
-
Stainless Steel (SS) should actually be called Stain-Less Steel. It only stains or rusts less that other steels. Blame this on marketing, making people believe their stainless steel tools are impervious to whatever.
-
@valvestem125 said:
Stainless Steel (SS) should actually be called Stain-Less Steel. It only stains or rusts less that other steels. Blame this on marketing, making people believe their stainless steel tools are impervious to whatever.I know that. In Dutch it's called rust-resisting steel (or something like that), but most people call it rust-free steel. (the difference between the words in Dutch is smaller: either "roest-vast staal" or "roest-vrij staal", which would both be abbreviated by RVS)
-
For surface rust I simply use Baking Soda on my finger or on a rag. Works wonders and is readily available. Clean with hot (dish) soapy water afterwards then rinse well. I use a air compressor and air dry to make sure all the water is out of my tool, but I assume towel dry and leaving in the sun will be efficient. Super easy and effective.
-
I actually used the oven to dry it after de rusting

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
That works too.