Adding a clip
-
It can be done. Syph has added clips to his custom alox mods. Maybe he will chime in with more info.
Also, welcome to MTO

-
I've seen this one from kinfekits.com recommended a lot
http://www.knifekits.com/vcom/product_info.php?cPath=60_101_379&products_id=2107I've been wondering though how you go about attaching it. No one seems willing to give up the info. Do you just drill holes, thread the screws in, maybe add a drop of loctite, and hope for the best? Does this work on cellidor scales as well?
-
@GnarShred said:
I've seen this one from kinfekits.com recommended a lot
http://www.knifekits.com/..._379&products_id=2107I've been wondering though how you go about attaching it. No one seems willing to give up the info. Do you just drill holes, thread the screws in, maybe add a drop of loctite, and hope for the best? Does this work on cellidor scales as well?
I don't know about Alox, but I'm quite sure it won't work on cellidor like that. You could try something like the Swissbianco pocket clip (see this link, about halfway down the page http://swissbianco.ca/products.htm)
-
Ya I love those little clips from knifekits. They come with 2-56 threaded screws, so you need a #51 drill bit and a 2-56 tap. Ive never done it with the scales on, but it should be possible. WIth the scales off I have the luxury of tapping right though, leaving them on you'd have to use a plug style tap meant for doing blind holes, but I dont see why it wont work.
-
@GnarShred said:
I've seen this one from kinfekits.com recommended a lot
http://www.knifekits.com/vcom/product_info.php?cPath=60_101_379&products_id=2107I've been wondering though how you go about attaching it. No one seems willing to give up the info. Do you just drill holes, thread the screws in, maybe add a drop of loctite, and hope for the best? Does this work on cellidor scales as well?
works just fine on cellidor. you need to undersize the drill bit and "tap" the plastic with the actual screw.
-
I've seen this one from kinfekits.com recommended a lot
http://www.knifekits.com/vcom/product_info.php?cPath=60_101_379&products_id=2107I've been wondering though how you go about attaching it. No one seems willing to give up the info. Do you just drill holes, thread the screws in, maybe add a drop of loctite, and hope for the best? Does this work on cellidor scales as well?
works just fine on cellidor. you need to undersize the drill bit and "tap" the plastic with the actual screw.
I always eondered about cellidor. Steve said he fills the hollow plastic with epoxy for more strength.
-
I will remove the scales, drill and tap screws, seems the best way. Thanks to the great posts I reviewed from Syph007.
I have a small mill and lathe, should help.
This should be fun. :D -
Remember to post pictures of the result. :D
-
@g flight said:
I will remove the scales, drill and tap screws, seems the best way. Thanks to the great posts I reviewed from Syph007.
I have a small mill and lathe, should help.
This should be fun. :DYou can leave the scales on ;). Just open all the tools and mark with a center punch. Then just drill and tap. After that it takes some grinding of the screws to get the length correct. Use cutting fluid for aluminum, it's helps more than you can think :)
-
Update! Got the knife apart without tragedy. Drilled and tapped the screw holes. Made my own clip with .032" titanium(like ti because it flexes easier than steel). Drilled for 1/8" threaded pivot pins(which I don't have yet).
Here is the "idiot proof" layout for reassembly.

This is my micro mill. Picture is a reenactment of how I removed the rivets as they were done previously.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
