Leatherman Bit Driver
-
The bit kit is unbeatable for its balance between portability, versatility, and quality. I want to use those bits with a standard hex driver...which is the opposite of folk usually want to do. While the bits fit, there is always too much play for it to be useful.
I found a topic here from a few years ago where a member made a driver, but there were no specifics as to how it was done, and maybe there have been some advancements since then.
An alternative is to cannibalize an existing Leatherman tool and incorporate the bit holder into a keychain-able tool.
Any ideas?
-
Was it me or zed? :D
We're talking about this, right?


The driver was ground to fit on a angle grinder but you can use a regular dremel too to make one. The only way to make the LM bits to fit though is to drill out the magnet on the bottom of the driver. otherwise the LM bits are too long. You could maybe epoxy some smaller neodymium magnets in there to have a magnetised driver again. But with the magnets sitting a bit lower than the standard driver to accommodate the longer bits.

BTW, no problem bumping an ancient topic here if it contains info on something you would like more details on. I know there's that 120 days notification, but we don't make too much fuss about that here. ;)
-
Its very easy to mod a standard 1/4 bit to fit a Leatherman bit holder

-
And even better to add one from tofty!

Shapeways
:) -
I think the OP here is more interested in using the Leatherman bit kit with a standard 1/4" driver like the bottom driver. As I said, I drilled out the magnet on that one. Now the LM bits slide in and can be used with the 1/4" driver and lick into place. The standard ones though now don't have the magnet to keep them in and can slide out if you turn the driver upside down.
-
I would suggest looking at the bit driver extender. Pics would help right, I'll be back shortly.
-
@enki_ck said:
I think the OP here is more interested in using the Leatherman bit kit with a standard 1/4" driver like the bottom driver. As I said, I drilled out the magnet on that one. Now the LM bits slide in and can be used with the 1/4" driver and lick into place. The standard ones though now don't have the magnet to keep them in and can slide out if you turn the driver upside down.Thanks. So removing the magnet eliminates all or most of the wobbling?
--Al
-
Yes, it allows the LM bit to slide in deeper so it's held in more tightly. As Zoidberg says, the original Leatherman bit extender will do the job better but this is a simple and cheap DIY solution to doing it with stuff you already have around the house.
-
Thanks, y'all.
I ordered the bit extender.
I found this thread:
http://edcforums.com/threads/universal-screwdriver-minimalist-carry.85713/I have the County Comm Torqkey, which will increase the number of tasks this setup can handle. The custom tool mentioned in that thread looks awesome. Too bad it's out of production.
I keep a Shröder ratcheting t-handled tap wrench in small belt pouch that I grab when needed. That tool holds the Leatherman bits perfectly, and disassembles to the size of a Wave.
-
@tattoosteve99 said:
And even better to add one from tofty!
Shapeways
:)Sorry brain fart.
But I like that small adapter from the link ;) -
I'm going to start hunting for that. If I find it as a single piece, I'll grab a bunch and send them out to anyone who wants for cost. Everyone should have a universal driver.
--Al
-
I got my Topeak Ratchet Rocket Lite in the mail today. It accepts the LM bits and, unlike with the otherwise awesome Chapman ratchet, it holds them in place. It's small enough that I can carry both it and the bit extender.
--Al
-
Pics please :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




