Swords and their history.
-
I was going to post this in the weapons of war thread...but thought that if I continue with the logical progression of each of the swords in my collection, it might sully that thread. So instead of doing that, I will post some sword history and the pieces I have in my own collection here. If anyone would like to contribute to this thread...by all means please do so.
First off, I am going to start of with my example of a Viking sword. Before I do so however, please follow the link to some real good Viking sword history and photographs.
My example is a Tinker Pearce Viking Sword collaboration with Hanwei. Tinker Pearce teamed up with Hanwei to produce a series of swords for both martial artist, re-enactment, and collectors. The one I have is sharp and not the blunt version.
Oakeshott Type: X
Peterson's Type: E
OAL: 37-3/8 inches
Blade Length: 30-7/8 inches
Blade Width @ Base: 2-3/16 inches
Blade Width 5 inches from point: 1-1/2 inches
Blade thickness at base: .200 inch
Blade thickness 1 inch from tip: .085 inch
Distal taper is Straight
Hilt OAL: 6-1/2 inches
Handle length: 4 inches
COG: 4-3/4 inches from base of blade
Blade Node: 20-1/4 inches from base of blade
Primary Hilt Node: On handle approx 1/2 inch from cross
Weight: 2lb 8oz.This sword was inspired by historical examples from the early 9th C. but was not copied from any specific sword, most notably finds from the area around Trondheim, Norway, where the circular indentation hilt decoration was popular. The scabbards are provided with suspension points and a period chape, giving the sheathed sword a very attractive appearance. The construction of the Viking "pair -sharp and blunt" differs from other swords in the Tinker series inasmuch as they are tang-riveted (peened) in period fashion at the pommel, primarily to satisfy Viking re-enactment requirements.
In use, it is important to hold the sword in the handshake grip, which will allow the pommel to slide past the heel of the hand. If you hold this type of sword wrong, the sharp end of the pommel will hit your hand and will cause a lot of pain to the user. In hindsight, Viking swords are not the most comfortable type of sword to swing around. The sword itself is fairly light and maneuverable and fairly sharp from the factory. There are some reports that some extra sharpening was required to get it up to speed...but I have found my example to be sharp enough. The Tinker Hanwei Viking sword is well built.
-
The Mortuary Hilt Sword, a subset of basket hilt swords of Britain.
Background history.
British Basket-hilted Swords
Descriptive catalogue with typology of a British sword-type with a 500-year history.
Google Books (books.google.ca)
The example I have is a Sir Oliver Cromwell Mortuary hilt sword replica produced by CAS/Hanwei. The original, which is said to have been held during the battle of Drogheda in 1649, is today found in the collection at the Royal Armories in Leeds.
http://en.wikipedia.org/wiki/Siege_of_Drogheda
The handle is is 10 3/4", and the blade is 32 3/4" long.
This sword is the most decorative I have in my collection. It is a rather striking and beautiful mortuary hilt sword. CAS/Hanwei gave the sword a nice antique application all over which adds to the overall beauty of this show piece.
The hilt has a key that sets the sword into the sheath nicely.
The scabbard has nice decorative chaps designed for a sword belt frog. The furnishings are nice with the antiquing applied to them.
The pommel is nicely decorated with a gold leaf motif.
The handle features real ray skin with a wire wrapping for added grip.
Accents include wire Turkish head knots on the pommel.
As you can see, the sword offers plenty of protection to the users hand.
-
Very nice sword Chaco. I always wanted to have a real sword since my wood ones as a kid

If I had the cash to spare I'd get me Zombietools Mac Daddy'O. :D
For now, I will just look at your pics. -
Third installment - Small Sword.
A little history of the small sword.
http://ahfi.org/weapon-descriptions/small-sword-court-sword-town-sword/
Typical of later styled small swords, this Cold Steel version features a triangular blade designed strictly for thrusting, and a common shell and light knuckle guard. The sword only weights 22.6 ounces. The small sword is a progression from the longer, heavier, and more unwieldy Rapier.
Specifications:
Blade Length: 31 1/4"
Overall Length:38 1/4"
Steel: 1055 Carbon
Weight: 22.6 oz
Handle: 7"
Scabbard: Leather ScabbardBecause this is a Cold Steel sword, you can't miss the usual Cold Steel video. ::)
Small Sword : Cold Steel Knives
I will have to say, the Cold Steel version of the small sword is beautiful and tastefully done.
The scabbard's hardware matches the sword nicely.
Here I am showing the light knuckle guard.
-
Thanks Microbe. I was always fascinated with military history, and for some reason, I love swords and sailing ships. I can't afford frigates and ships of the line, but I can indulge my interest with swords. I tried to get some key examples from the long history of swords. So I have a little of almost everything...it is by no means an extensive collection, and I do have holes in it from a purely historical timeline point of view. I have tried to stay away from purely decorative swords, preferring what people call "battle ready" swords. I still have my first which was a gift from my parents when I was in grade 10. It is a cheap Toledo junker that I have held onto for sentimental reasons.
-
Very nice Chako.
I currently don't have any swords, though two I'd love to have (preferably originals, but I'll take a good quality replica) are the US Army's Model 1850 field officer's sword and the Model 1860 Light Cavalry Saber. I've seen originals for sale. One day...... 
-
Excellent Thread
sorry I don't have anything to contribute
-
Forth installement - 1796 Light Cavalry Saber.
Some background history.
http://en.wikipedia.org/wiki/Pattern_1796_light_cavalry_sabre
The example I have here is produced by Cold Steel and comes with a polished steel scabbard.
Cold Steel 1796 Light Cavalry Saber
Now this is a terrifying weapon to hold and to look at. This Saber is a pure slashing weapon that can also be used for thrusting. In fact, this weapon was so terrifying on the battlefield that the French wanted it removed from the conflict.
Specifications:
Weight: 34.2 oz.
Blade Thickness: 5/16"
Blade Length: 33"
Handle: 4 3/4" long
Steel: 1055 Carbon
Overall Length: 37 3/4"Now this Cold Steel version is a fairly close approximation to the real thing. Some minor handle variations are evident if you had this sword next to a real 1796 Light Cavalary sword. With that said, mostly everything is correct. Super sharp and all.
-
Fifth installment - US Marines Mameluke Ceremonial Sword.
A little history.
http://en.wikipedia.org/wiki/Mameluke_sword
http://www.mca-marines.org/gazette/article/history-mameluke-sword-united-states-marine-corps
This sword is certainly one of the more flashy swords in my collection. Like all military ceremonial swords the world over, this one features a stainless steel blade that is not sharpened except for the point. This sword came with a sword bag and the usual military steel scabbard.
-
Jerseydevil, I mostly have good quality replicas. Originals are hard to come by for the most part.
JAfromMn, that is ok.
-
Sixth installment - Hanwei Renaissance Side Sword.
Some background history.
http://en.wikipedia.org/wiki/Spada_da_lato
http://www.strongblade.com/history/rapiers.html
This sword is simply beautiful, superbly balanced, and extremely sharp from the factory. Designed to both cut and thrust, the side sword is considered to be a precursor to the longer Rapier...however, the sword existed alongside the Rapier and has seen use right up to the American Civil War. Although the Rapier was mostly favoured by civilians, the military quite often preferred the side sword.
Statistics
Blade Length: 30.0"
Handle Length: 6.0"
Overall Length: 38.0"
Guard Width: 8.0"
POB (Point of Balance): 0.50"
COP (Center of Percussion): about 20.0"
Weight: 2 lbs 4ozThe grip features beautiful wire work.
-
Seventh installment - Camel bone short sword.
I do not know much about this other than it was dirt cheap as far as swords go. I bought it at a local shop that sells East Indian/East Asian decorative goods. I was looking for a dagger to decorate a wall, and found this instead which fit the bill nicely.
Surprisingly enough, even though the blade is hand made and roughly at that, it is razor sharp. Furthermore, for the price, the handle exhibits a little movement especially towards the pommel end...but not as much as one would expect. This decorative item is rather functional and serviceable. The blade however is made of stainless steel which is inferior to carbon steel...but then, for something designed to be hung on a wall that is ok. I am still puzzled over why they sharpened the blade in the first place.

The scabbard is of cheap design. Leather upper and lower sandwiching a foam core. Standard cheap scabbard. It does look ok hanging on a wall however. So no complaints here.
-
Wow! Nice read and pics! I love swords. Thanks for sharing.
that's us mobile
-
Eight installment - CAS/Hanwei Mercenary Sword.
A little longsword history to start things off.
http://en.wikipedia.org/wiki/Longsword
This sword is a beast that come in at 4lb 8 ounces. The Mercenary is an imposing sword in the 15th century style. This sword comes with a triple-fullered blade, steel S-curve guard and scent stopper pommel. Supplied with a leather-covered belt scabbard around a wood frame.
Statistics.
Forged High-Carbon Blade
Weight: 4lb 8oz
overall Length: 47 1/4'' Blade: 35 1/8''
P.O.B.: 4''
Thickness: 5.6 mm - 4.7 mm
Width: 51.8 mm
Grip Length: 8 3/4''
Pommel: PeenedThis sword is longer than my 4 foot table.
A big two handed sword with not very sharp edges...mostly designed to stab into weak spots in armor, or to bludgeon armored foes into insensibility.
-
Here is my modest collection of Swords
Longsword 1350–1550
In my case its overall length is 122cm and weights just about 1.3kg. The blade is double edged, 91cm of length (unsharpened as I use it for training). The hooked guard is made for disarming. Center of balance is 5cm in front of the guard. Center of percussion is 30cm from the tip.
The longsword is a thrusting sword. Thrusting is very precise you can hit a fly with a thrust, its also very fast.Oh yeah and a remark if you parry a swordstroke, you glide in, meaning you do not block the opponents blade but you let it glide along yours to take the blow (except for the low blows, very difficult to glide there). As a result you get a screetching sound (metal scrapping on metal). This is also the reason why my blade, after a year of abuse is still in such excellent condition.
Oh and next to my Longsword, you can see a typical Meyer Fencing Feather (tip of the blade is very elastic and bends when you thrust). The design dates back to the early 16th century. And thanks to that thick blade part, close to the guard you get similar weight and balance as in a normal Longsword.
Oh, and I got scooped


-
Fascinating stuff and excellent detailed photographs as always.
Thanks for the links to all the historical information.
The Mortuary Hilt Sword is a very attractive piece, and I found it interesting to read about how the basket-hilted type sword was probably developed in response to a change in sword fighting style. I am tempted to go on a mission to the Royal Armouries to see if I can locate Cromwell's sword.

Also, the Cold Steel small sword video was the funniest thing I've seen this week.

-
Etheralicer, those look very nice.
Spatha, all Cold Steel videos are mall ninja funny.
-
I love this thread.
-
Ninth installment - Hanwei Tinker Pearce Longsword.
Here are a few longsword links to start.
http://www.lordsandladies.org/longsword.htm
http://www.worksofrichardmarsden.com/historyofthelongsword.htm
Now onto this particular sword. Tinker Pearce is a fairly well known sword maker, and he teamed up with Paul Chen of CAS/Hanwei to produce a few Tinker Hanwei collaboration swords. The biggest focus of this series, most of them come with either a sharp or blunt blade which are easily interchangeable via a threaded tang and a hollow tubular nut that fits flush into the pommel. You can easily replace a damaged blade via a hex key, or buy a sharp and blunt blade for the best of both worlds. The nice thing about these swords, the blunt and sharp blades are carefully balanced and weigh the same for practice and cutting.
Specifications.
Oakeshott Type: XVIIIa
OAL: 47-1/4inches
Blade Length: 35-1/4 inches
Blade Width @ Base: 2-1/8 inches
Blade Width 3-1/2 inches from point: 3/4 inch
Blade thickness at base: .254 inches
Blade thickness 2 inches from tip: .090
Distal taper is convex
Hilt OAL: 12 inches
Pommel Type: T-1
Guard Type: 2
Sword Family: n/a
COG: 3-1/2 inches from Base of blade
COP: 21-1/2 inches from base of blade
Weight: 2lb.15oz.
Steel: 5160 Spring SteelThis sword is very light and fast for its size. This is the sharp version, and it came very sharp from the factory.
Overall, this is one fantastic longsword. The balance feels just right, making this one super quick sword to use. There is a misconception out there that longswords are big heavy brutish things that require a lot of strength to use. 5 seconds with this sword in your hands would dissuade anyone of that mistaken concept.
-
These are lovely, Chako.
You've got me looking at swords now!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login































































