Rebar+
-
I thought some people might be interested in seeing my new Rebar.

Given that I don't like the Rebar's blades and carry a separate knife, having two additional useless blades was a bit silly and it's also problematic for UK carry outside of work. You may see, therefore, that not having blades may be an advantage as I can pair it with an appropriate knife and use the space they free up for more useful things.
Leatherman tools come in basically 3 different sizes: thin (can opener), thick (flat driver) and double (Phillips driver). The doubles are twice the width of the thick tools or triple the thin tools. There is a bit of variation but most things fit that pattern.
A normal Rebar has:
File: Thin
Lanyard ring: Thin
Small driver: Thin
Awl: Thick
Large Flat: Thick
Plain edge: Thin
Saw: Thin
Phillips: Double
Spacer: Thin
Can opener: Thin
Serrated edge: Thin
This leaves two thin components on each handle that I don't want, the spacer, lanyard ring and blades. As you will see later, my maths doesn't entirely add up. Put that down to me being a stupid Brit eh?
So what do add instead? Well, I really like the bit driver, because it adds lots of options and gives you a much better steel so I decided to put that in. I also experimented with putting some scissors in, they so nearly fit but the top of the thumb pad catches on the plier springy-bit and means that the jaws won't entirely shut.There's quite a lot of flexibility with where you place the components in the handles but there are also a lot of combinations that won't work. I had a lot of playing around trying to get it all right. Too much in the handle and the pivot doesn't got far enough across in to the opposite handle and you get horrific tool wobble. Too little in the handle and you can't tighten the pivot up enough. There really isn't much leeway. What I have ended up with is pictured below, but what might not be clear is that of the two little brass washers in each handle on side now has only 1 and the other side has 3. The side with only 1 has a Fuse lanyard ring in because it's very thin.
Now for the pictures. Sorry for the lack of quality, they're taken over two nights with two different but equally rubbish phones and poor lighting.
This is the side the screw comes out, it's opposite on the other side. If you look at the pivot screws, one of them has a fatter head and the other has a slight neck to it. The fatter one is the one that unscrews:

Scissors problem


Finished!


Everything works, everything opens smoothly and locks up well with less play than there was when I started. You can't do the trick of closing the handles on to the open pliers and sliding the pliers closed along the tools (you know that little nub inside the Wave's handle?) but oh well.
Where from here? Well the can opener is completely redundant for me. I need to grind some material off the small screwdriver so make it fit the screw that I need it to fit. I'd like a medium flat driver but I might just use a non-shrunk small one. That's about it really I think

Many thanks to lowtech for the bit driver

-
Great work! I really like the added bit driver.

-
good work Tom mate

shame about the scissors though
-
Always good to see someone making a tool their own.
You were welcome to teh Bit Driver - thanks for the trade! -
Nice one Tom, finally,a useful Rebar!
-
Very nice work.
The world belongs to the funkiest.
-
very nicely done. an excellent choice of tools, especially if you carry a knife separately.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login