Wave Issues
-
As said above oil and use should loosen it up.
-
There's sometimes a bit of grit in there from packaging and shipping. It should work its way out with the oil and motion.
The world belongs to the funkiest.
-
Thanks for the responses folks!!

I had oiled it pretty well after the cleaning but it was stiff and I was a little afraid of playing with it. But today I picked it up and the pliers were much better!! I really appreciated all the help!!
Sadly there are a few other minor issues. The SE blade don't close properly, it hits the handles so I need to push it against the liner for it to close. I've tried to tighten/loosen the pivot in every possible way and it still hits the liner in the same spot. :'(
The last and probably the smallest of the problems is a "click" that the lock tab does every time I unlock the large flat head. The scissors and the eyeglass screwdriver don't present such problem
Any ideas of what may be happening??.jpg)
.jpg)
-
WRT the "click", all mine do that. Assuming it's the same problem, you may find that it improves if you push the tool up towards the lock.
-
@Cupboard said:
WRT the "click", all mine do that. Assuming it's the same problem, you may find that it improves if you push the tool up towards the lock.I actually tried that, but without much success. But as I said it isn't a huge problem, it is mostly me being picky. I think my expectations were a little too high.
Thanks a lot for your response!!!

-
I checked my Wave. It has the same click on unlocking the large flathead. I think it's a matter of the shape of the flathead's lock-catch, and the shape of the lock itself. Looks to be completely normal for the model, and doesn't affect function, so I wouldn't sweat it.
There's a slight undercut to the lock catch on the flathead. While it's the same flathead as is used on the Rebar, the Rebar's lock is angled somewhat differently, so doesn't click when disengaging.
-
@Lynn LeFey said:
I checked my Wave. It has the same click on unlocking the large flathead. I think it's a matter of the shape of the flathead's lock-catch, and the shape of the lock itself. Looks to be completely normal for the model, and doesn't affect function, so I wouldn't sweat it.There's a slight undercut to the lock catch on the flathead. While it's the same flathead as is used on the Rebar, the Rebar's lock is angled somewhat differently, so doesn't click when disengaging.
Thanks for passing by Lynn!! As I said I can be a pain in the behind to please, so the click is a little annoying but it definitely doesn't affect the function. Sorry for being so annoying!! :P
-
Hey WWW, I just checked my wave and it also clicks as you stated. I didn't investigate much more to find out why as I obviously haven't noticed it before. The knife blade hitting the handle is not good at all, I'd send it back or have it fixed under warranty. My Surge main blade comes real close to hitting the inside handle when closing but it doesn't touch. Sorry to hear the Wave wasn't exactly as you expected but know that LM will make it right for you. I don't know if the clicking will be resolved however.
-
@Aloha007 said:
Hey WWW, I just checked my wave and it also clicks as you stated. I didn't investigate much more to find out why as I obviously haven't noticed it before. The knife blade hitting the handle is not good at all, I'd send it back or have it fixed under warranty. My Surge main blade comes real close to hitting the inside handle when closing but it doesn't touch. Sorry to hear the Wave wasn't exactly as you expected but know that LM will make it right for you. I don't know if the clicking will be resolved however.The clicking as I said, is not a huge issue. And I'm not sure if I was expecting too much or what, but it sure is a great tool. And if remove my bias towards the tool load out of the equation, most of my complaints are related to whether cosmetic or comfort issues. As for sending it to repair, that's a no-no. It took more then 3 months for it to show up, not fault of the seller but of the guys from customs, I'm afraid that if I send it off it will never come back. Thanks for passing by!!

-
WRT the "click", all mine do that. Assuming it's the same problem, you may find that it improves if you push the tool up towards the lock.
I actually tried that, but without much success. But as I said it isn't a huge problem, it is mostly me being picky. I think my expectations were a little too high.
Thanks a lot for your response!!!

edit: I kept trying and eventually I got the hang of it, not sure what I was doing wrong but now I'm able to close it more silently!

-
Glad you got it sorted. my wave came with very sharp edges all over and needless to say i was surprised. I felt that the best selling tool should have been in better shape. I smoothed down all the edges and oiled it because it was also very stiff. This is my work tool and I've carried it pretty much daily, I have only the highest praise for the wave.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

