Preventing rust?
-
Just oil them every now and again. Also don't store them for long periods of time in there sheaths.
that's us mobile
-
Q. How do I avoid my LM rusting?
A. Buy a Swisstool.

-
This is a side question, but if I take apart my Leatherman to clean it, like minor rust spots or lint that got caught in the sides of the plier head, does that void the warranty if I put it back together the same way or do I have to send it to them to get it cleaned?
-
Yes it would void your warranty if you take it apart. On the plus side there is no need to take it apart to clean it.
Edit: forgot to mention, Leatherman will not do a cleaning if you send it in. They do not offer such a service that I know of.
-
@captain spaulding said:
Yes it would void your warranty if you take it apart. On the plus side there is no need to take it apart to clean it.Edit: forgot to mention, Leatherman will not do a cleaning if you send it in. They do not offer such a service that I know of.
But mine does need a cleaning, what should I do?
-
Wash it with some soapy water and use an old toothbrush. Then dry it out and oil it. Then your good to go.
that's us mobile
-
If the pliers teeth are grungy then use a brass wire brush with either WD40 or 3and1 oil. Old tooth brush works great for all other parts so you dont scratch it up or you can use 0000 steel wool or brass wool and WD40/3and1 oil.
Mine was used and was pretty dirty so I did all of the things I mention and then polished it shiny 8)

-
Were you able to clean out the pivot area?
-
I believe I got into every nook I realistically could but yes disassembly is best. I didn't want to void my warranty though. You can spray WD40 and let it soak over night in the pivot areas.
-
I live in a temperate region that sees slightly above average rainfall. I live many hours from any sea or ocean.
I have never had a LM rust under normal use. Not one. Neither in storage, nor during EDC sheath carry. I do have some small rust spots on my Vic Spirit (though I admit I have never oiled it).
Things I do not do:
-
Put tools away wet. Ever.
-
Put tools away dirty.
-
Store MTs or knives in a tool box with other non-stainless tools.
-
Store tools in an environment without temperature and humidity control such as a shed or garage or vehicle.
Things I always do:
-
Keep my tools clean and dry.
-
Store them indoors where there is climate control. This includes the ones I carry EDC. They stay in the bag or sheath, but the bag and sheath stay indoors with me.
-
Oil them on occasion. (Usually this means place on towel, spray down with WD 40, wrap in said towel, let soak in over night, wipe off with clean towel)
-
Throw one of those small desiccant pouches or canisters in my bag or drawer just as an extra precaution. They come in everything these days. Save and use them.
The only time a LM rusted on me was when I left wet drywall mud on the saw of my Supertool 200. Spots of rust appeared and bled through the mud. I scrubbed it off three days after the fact with a Scotchbrite pad. No lasting effect at all. You'd never know.
My Spirit has small rust flecks on the inside of the tool. I admit I have never oiled it and should have. If I had treated it like my LMs, it would not have this minor rust. It also does not bother me at all, and someday I'll clean it off and start oiling it.
My Gerber Pro Scout did rust on the outside of the handles. That's the worst I have seen with rust on an MT. That was an EDC tool for many years, saw mild abuse, and did not get oiled enough by my own admission.
I do believe that oiled black oxide is the way to go in a salt or wet environment, but you still have to stay on top of the clean/dry/oil cycle.
Based on my experience with.. Seven different LMs over the course of about twenty years.. All of which have been EDC at some point in a sheath on my belt or the sheath on the outside of a bag.. All of which except my Rebar and my Flair having been used on construction sites, in a shop, around the home, and in the outdoors.. And all of which have seen every season of weather..
..I can only conclude that if your LMs rust and you don't live right off the ocean, you are not caring for them as I do. And if you did, you wouldn't have any issue.
If you live near the sea and it is humid there or misty or damp as well, you have a host of other issues from the salt air mixed with damp. Dry down religiously, oil weekly, or find a steel that survives your area. Otherwise, good luck.
For the rest of you, shush already. Tools require care. Get to it.
-
-
@Breezy12 said:
very well said, glorn. your entire post was excellent, but I especially liked the last bit...Tools require care. Get to it.

+1

I live in an environment that goes from freezing cold to cold and wet to mild and wet to hot and humid over the course of a year. I take my tools out in the woods, out fishing, in the snow, etc.
Proper maintenance and good habits have prevented any of my LMs Gerbers, SAKs, Swisstools from rusting over the 9+ years I've been carrying and using them.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login